2004 Toyota MR2 Spyder Logo

Related Topics:

A
Anonymous Posted on Jul 11, 2014

Reverse light wiring diagram

What is the colour code for the reversing light wires Reversing light wires colour code

5 Related Answers

Anonymous

  • 97 Answers
  • Posted on Jul 16, 2008

SOURCE: REVERSING PROBLEM

doest it idle lumpy, when driving forward, do the revs stay below normal when ideling, if so, the reverse gear may be damaged and have not sufficient power in revs to make this gear work, check with your mechanic, it wont cost anything for them to check it.

Ad

Anonymous

  • 1861 Answers
  • Posted on Nov 03, 2008

SOURCE: tow hitch wiring diagram

Send me your e-mail address, and I will send you a .pdf of the entire rear lighting wiring;
FixYa is not set up to post .pdfs yet.
Glad to help, and thanks for choosing FixYa.

Anonymous

  • 2559 Answers
  • Posted on Jun 03, 2009

SOURCE: i need a wiring diagram for my bluebird

Here you go.

Battery: blue/yellow
Accessory: gray
Ground: brown
Illumination: green
LF speaker (+): pink
LF speaker (-): violet
RF speaker (+): light green
RF speaker (-): blue
LR speaker (+): black
LR speaker (-): yellow
RR speaker (+): red
RR speaker (-): white

Anonymous

  • 6 Answers
  • Posted on Sep 26, 2009

SOURCE: wire colour coding for radio Holden Nova LF

Car Radio Constant 12v+ Wire: Blue/Yellow
Car Radio Switched 12v+ Wire: Gray
Car Radio Ground Wire: Brown
Car Radio Illumination Wire: Green
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Pink
Left Front Speaker Negative Wire (-): Violet
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Blue
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Black
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Red
Right Rear Speaker Negative Wire (-): White

Anonymous

  • 1986 Answers
  • Posted on Oct 01, 2009

SOURCE: Reversing lights don't work.

On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer
0helpful
1answer

How to change the rear light on a Peugeot 2008 GT premium 2021 EAT8

Great advice. Take it to an alarm installer. 15 minute job done right for about 50 bucks.

Or risk it, rear white light, find the wire.

https://www.google.com/search?q=change+the+rear+light+on+a+Peugeot+2008

And how to wire to a reversing light.

https://www.google.com/search?q=peugeot+2008+reversing+light+wiring+diagram

..
1helpful
1answer
0helpful
1answer

We have a 2011 ford f350 and are trying to t/s the reverse lights. we checked the fuses. what else might it be. we cant find a diagram to the wiring.

In the BJB - battery junction box under the hood ,is a reversing lamp relay. Check it or try a known good one !an check fuse F70 10amp in the BJB .

Reversing Lamps

The reversing lamp system consists of the following components:

  • Rear lamps
  • Reversing lamp switch
  • PCM
  • BCM

When the transmission is placed in REVERSE (R), the BCM provides voltage to the reversing lamps. The reversing lamps are located within the rear lamp assemblies.
When the transmission is in REVERSE, the PCM (gasoline engine) or the Transmission Control Module (TCM) (diesel engine) sends a message over the High Speed Controller Area Network (HS-CAN) to the Body Control Module (BCM) indicating the transmission is in REVERSE. The BCM provides voltage to the reversing lamps when it receives the message that the transmission is in REVERSE and the ignition is in the RUN state. You could have a transmission range sensor problem , check to see if it is adjusted correctly ! Need to have a scan tool to make sure the BCM is receiving signal from the PCM . This is complex for someone who doesn't deal with or know about serial data communications ! All it is ,is electric inputs to a control module, then the control module configures it into data bits an bytes 1's an 0's then sends it out on the Data bus. The module that needs this info reads it an turns on the lights.This system can set codes in the bcm ,leading to a problem.

  • DTC B1277:11 (Reverse Lamp: Circuit Short To Ground) - a DTC that sets when the BCMdetects a short to ground from the reversing lamp output circuit.
  • DTC B1277:15 (Reverse Lamp: Circuit Short To Battery or Open) - a DTC that sets when the BCMdetects an open from the reversing lamp output circuit.
  • Could set codes in the PCM - powertrain control module for a transmission range sensor problem !
  • 2helpful
    1answer

    What colour are the live/earth wires to the reversing light on a lexus rx500

    I am sorry but we don't have wiring diagrams here at fixya because the diagrams are copy protected. You can download the diagrams for a small fee here.
    0helpful
    1answer

    Montero/Shogun 1998

    order and buy the book at sprints auto
    the wiring diagram will tel you all you need
    1helpful
    1answer

    Fit rear parking sensors to volvo v70 But need to know the wiring colour for the reversing lights

    look at the sockets where the bulbs go into the back up lights and note the colour of the wires
    Not finding what you are looking for?

    231 views

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    ROBERT GARCIA
    ROBERT GARCIA

    Level 3 Expert

    926 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...