How to replace lines brake proportioning vale plumbing honda civic 1993

are you trying to bleed the lines or is it no brake pedal? anytime you change brake lines bleeding is hard the best way is fill master cylinder leave top off careful brake fluid will eat the paint then open the two frnt bleeder vales let gravity bleed then it might take up to 5 minutes once fluid starts to flow shut the bleeder vale this should help you good luck Mike

Also called a "brake proportioning vale". It regulates (proportions) brake fluid pressure between front and rear wheels during braking.

have you checked your E brake switch? or foot brake switch under dashboard? you might need to re adjust for proper functionality.

My 1991 civic did the same thing and it Turned out to be a fuse under the hood. At the same time the door dinger would ding when I hit the brakes and I had no horn.

I, feel sorry for you, after reading your problem, but don't worry you visit the Reliable-Store they will help you for sure.Here's the link.
Honda Civic del Sol Service Repair Manual 1992 1993 1994 1995

1. replace your spark plugs
2. are your still running on carburetor? if yes, have it cleaned and check if the air/fuel ratio is correct.

here is a 96 taurus


Item Part Number Description 1 2C296 Anti-Lock Brake Tube 2 2C219 Anti-Lock Brake Module 3 2005 Power Brake Booster 4 2263 Front Brake Tube 5 2B091 Brake Pressure Control Valve 6 2140 Brake Master Cylinder 7 2B547 Brake Load Sensor Proportioning Valve 8 N802191-S60 Bolt 9 2L568 RH Rear Brake Tube 10 2L569 LH Rear Brake Tube 11 2C287 Brake Fluid Distributor Tube 12 N808531-S301 Bolt 13 — Front Side Member 14 N802324-S56 Bolt 15 18124 Front Shock Absorber 16 2B121 Front Disc Brake Caliper 17 2078 Front Brake Hose 18 2264 Front Brake Tube 19 2553 Rear Disc Brake Caliper 20 2A442 Rear Wheel Brake Hose 21 N808728-S60 Bolt 22 — Side Rail 23 N802324-S60 Bolt
Brake Load Sensor Proportioning Valve


Item Part Number Description 1 2B547 Brake Load Sensor Proportioning Valve 2 — Body 3 N802191-S56 Bolt (2 Req'd) 4 2L568 Brake Tube Assy 5 2L569 Brake Tube Assy 6 2265 Brake Tube Assy 7 2B255 Brake Tube Assy 8 5500 Rear Suspension Arm and Bushing 9 W611634-S301 Bolt A — Tighten to 11.4-15.6 Nm
(8-12 Lb-Ft) B — Tighten to 10-14 Nm (7-10 Lb-Ft)

Brake Hose, Rear —Drum


Item Part Number Description 1 — Rear Side Rail 2 2L569 Rear Brake Tube 3 N602324-S60 Screw 4 N611193-S60 Screw 5 2C023 Left Hand Rear Hose and Connector 6 2210 Rear Drum Brake Backing Plate 7 18125 Rear Shock Absorber 8 2267 Rear Brake Tube A — Tighten to 16-20 Nm (12-15 Lb-Ft)

the stratus is know for clasped rear brake hoses .This stops the flow off brake fluid. try opening the brake lines at the master cylinder that go to the rear.pump up brakes first! if you got fluid than check the brake line if this is rear disc brakes on the line at the rear will be a built in proportioning valve.if drum loosen rubber hose line before the rubber part to see if you have fluid. If you do replace the brake hose! On you 74 challenger by the way i love dodge! any way on the valve there is a small button on the front of the proportioning valve that pops out it needs to be tap in lightly. also hit the brake peddel kind of hard a couple off times if that doesn't work. thanks for your question


p.s that hex bar on the is a junction not a proportioning valve .

Sounds like you might have a caliper that is stuck and is not fully disengaging. If it is in the rear then you may have a bad rear caliper. Twoo things you can try. One is to crawl under the ca and adjust the tension two nuts on the emergency brake line. If that does not resolve the problem then remove the back tire and try to spin the drum or rotor whichever you may have. If it does not spin then try adjusting the e brake cable more if it still does not respond then you need to do a brake rebuild. Also does it pull while it is dragging? If it is then you will need to rebuild the brakes no matter what.

no the switch on the break pedle is bad