2004 gmc sierra 2500 dtc code p0174,system too lean bank 2. what is the cause?

Question edited for clarity. It is P-Zero 0, not P-oh O.
Please always include 'year make model' first 3 words, or it it is difficult to answer and some vehicles are slightly different or more precise and will show known issues.

P0174 - OBD-II Trouble Code Fuel System Too Lean (Bank 2)

https://repairpal.com > obd-ii-code-p0174
When a vehicle has the fault code P0174, it means that computer can no longer automatically adjust the mixture between air and fuel. Code P0174 applies to V ...

P0174 OBD-II Trouble Code: System Too Lean (Bank 2)

https://www.yourmechanic.com > Articles
Code P0174 indicates that there is a lean condition detected by the Engine Control Module (ECM). A lean condition will be created if there is too much air, and ...

P0151 Code - What Does It Mean & How To Fix It - OBD2PROS

https://obd2pros.com > dtc-codes > p0151
A P0151 code is caused by an ECM (Engine Control Module) receiving a signal indicating the O2 sensor for bank 2 sensor 1 has failed to increase the voltage ...

Code P0171 - System Too Lean: Symptoms, causes, common ...

https://www.samarins.com > diagnose > p0171
Jul 10, 2021 - The OBDII trouble code P0171 - System Too Lean (Bank 1) means that the engine air-fuel mixture is too lean, or there is too much air and too ...

DTC P0171: Fuel Trim System Lean Bank 1
DTC P0172: Fuel Trim System Rich Bank 1
DTC P0174: Fuel Trim System Lean Bank 2
DTC P0175: Fuel Trim System Rich Bank 2

Circuit/System Description
The engine control module (ECM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy, and emission control. Fuel delivery is controlled differently during Open Loop and Closed Loop (CL). During Open Loop, the ECM determines fuel delivery based on sensor signals without heated oxygen sensor (HO2S) input. During CL, the ECM adds HO2S inputs and level of purge to calculate the short and long term fuel trim (FT) adjustments. If the HO2S indicates a lean condition, the fuel trim values will be above 0 percent. If the HO2S indicates a rich condition, the FT values will be below 0 percent. The short term FT values change rapidly in response to the HO2S voltage signals. The long term FT makes coarse adjustments in order to maintain an optimum air/fuel ratio. A block of memory cells contain information arranged in combinations of engine RPM and engine load for a full range of vehicle operating conditions. The long term FT diagnostic is based on an average of cells currently being used. The ECM selects the cells based on the engine speed and load. The FT diagnostic will conduct a test to determine if a rich failure actually exists or if excessive vapor from the evaporative emission (EVAP) canister is causing a rich condition.
If the ECM detects an excessively lean condition, DTC P0171, P0174 sets. If the ECM detects an excessively rich condition, DTC P0172, P0175 sets.


DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1

Circuit/System Description
The engine control module (ECM) uses the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor pulses to monitor the correlation between the crankshaft and camshaft position. The crankshaft reluctor wheel consists of a 60-tooth pattern with 2 teeth missing for a reference gap. Each tooth is evenly spaced 6 degrees apart, except for the reference gap. The camshaft reluctor wheel has 4 teeth, 2 narrow and 2 wide. The 4 trailing edges of each tooth are evenly spaced 90 camshaft degrees apart. As the crankshaft rotates with the CMP actuator in the home or parked position, the ECM expects CMP sensor pulses to occur 36 crankshaft degrees before top dead center (BTDC) at cylinder number 1, and every 90 camshaft degrees thereafter.

• DTC P0171 Fuel Trim System Lean Bank 1
• DTC P0174 Fuel Trim System Lean Bank 2
.
The engine control module (ECM) controls the air/fuel metering system in order to provide the best possible combination of driveability, fuel economy, and emission control. Fuel delivery is controlled differently during Open and Closed Loop. During Open Loop, the ECM determines fuel delivery based on sensor signals without oxygen sensor (O2S) input. During Closed Loop, the O2S inputs are added and used by the ECM to calculate short and long term fuel trim (FT) fuel delivery adjustments. If the O2S indicates a lean condition, FT values will be above 0 percent. If the O2S indicate a rich condition, FT values will be below 0 percent. Short term FT values change rapidly in response to the heated oxygen sensor (HO2S) voltage signals. Long term FT makes coarse adjustments in order to maintain an air/fuel ratio of 14.7:1. If the ECM detects an excessively lean condition, DTC P0171 or P0174 sets.
Diagnostic Aids
• Excessive resistance in the fuel injector ignition 1 voltage circuit or the fuel injector control circuit may cause the following symptoms:
- Lean condition
- Misfire
- Rough idle
• The system will go lean if an injector is not suppling enough fuel.
• A lean condition could be present during high fuel demand.
• A malfunctioning MAF sensor can cause this DTC to set. Refer to DTC P0101 .
• Review the Failure Records with a scan. If an intermittent condition is suspected, refer to Intermittent Conditions .

DTC Descriptors
This diagnostic procedure supports the following DTCs:
• DTC P0420 Catalyst System Low Efficiency Bank 1
• DTC P0430 Catalyst System Low Efficiency Bank 2

This code could mean the catalytic converter on that bank has failed .

Causes of lean condition trouble codes P0171 P0174 GM 5 3L

P0420 P0430 catalytic converter catalyst inefficiency code diagnosis

P0300 is a random miss fire , a vacuum leak can cause this as well as low fuel pressure ! weak fuel pump , clogged fuel filter !
DTC P0171: Fuel Trim System Lean Bank 1
DTC P0174: Fuel Trim System Lean Bank 2 These two codes are saying the PCM - engine computer is see a lean condition .
DTC P0191: Fuel Rail Pressure (FRP) Sensor Performance
Circuit/System Description
The fuel pressure sensor is located on the fuel line. The fuel pressure sensor monitors the fuel pressure in the fuel line. The fuel pump flow control module (FPCM) monitors the voltage signal from the fuel pressure sensor.

You don't say what make , model an year vehicle ! These are for GM vehicles , yours could mean something else . Except the first three , those are genaric codes , same for all makes ! So can't say what this codes are P2097, and P2099 ! Can't mean this P2097 - Post Catalyst Fuel Trim System Too Rich Bank 1
P2099 - Post Catalyst Fuel Trim System Too Rich Bank 2

DTC code PO400 could be caused by a clogged EGR valve or EGR tube. try cleaning the EGR valve, tube
DTC code PO171 is fuel system too lean bank 1
DTC code PO174 is fuel system too lean Bank 2
Most likely suspects are O2 sensors, But can be caused by vacuum leaks and also can be Mass airflow sensor (MAF) try cleaning with electrical parts cleaner
DTC code PO 302 is a misfire at cylinder # 2
Check spark plugs and wires
Try cleaning the EGR Valve first along with changing the spark plug first, and see if any codes erase, in other words start with the cheaper fixes first, as some problems can be causing the other other codes

Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 2 is generally the side of the engine that doesn't have cylinder #1.

Note: This DTC is very similar to P0171, and in fact your vehicle may show both codes at the same time.

Symptoms: You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.

Causes: A code P0174 may mean that one or more of the following has happened:
* The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
* There could be a vacuum leak downstream of the MAF sensor.


Possible solutions include:
* In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
* Inspect all vacuum and PCV hoses, replace if necessary
* Check for a dirty fuel filter and proper fuel pressure


Hope this helps (remember to rate this answer).

code P0761-
Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 3 valve
- Shift solenoid 3 valve harness or connectors
- Shift solenoid 3 valve circuit is open or shorted
P0761 FORD Description Shift solenoid valve 3 is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module (ECM) (throttle opening). Gears will then be shifted to the optimum position. When is the code detected? The P0761 code is detected when the ECM has detected a mechanical fault with the solenoid energized, valve stuck off code O1744- is not a code these are the ones I have found that come close
P0174 1999 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2000 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2001 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2002 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2003 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 FORD Fuel Injection System Too Lean Bank 2

your car is probably running rough
its sucking air from the intake mininfold
is your intake maninfold plastic? but your veicle is defenetly having a vaccum problem

DTC code p0174 means "System too lean (Bank 1)"

Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exahust). On V6/V8/V10 engines



, Bank 2 is generally the side of the engine that doesn't have cylinder #1.

P0171 indicates a lean condition. The most common cause of this is a defective mass air flow sensor. Also check if any vacuum leaks. P0174 OBD-II Trouble Code

Technical Description

System Too Lean (Bank 2)

What does that mean?

Basically this means that an oxygen sensor in bank 2 detected a lean condition (too much oxygen in the exhaust.

Note: This DTC is very similar to P0171, and in fact your vehicle may show both codes at the same time.

-----------

Thanks.