Cars & Trucks Logo

Related Topics:

t
thurmon Posted on Dec 01, 2013

1996 gmc sierra 7.4 distributor cap removal - 1999 GMC Sierra 3500

5 Related Answers

Anonymous

  • 14 Answers
  • Posted on Feb 27, 2009

SOURCE: Tail light problems on 1996 GMC Sierra pickup

I had similar problem with my 97 sierra... I only lost 1 light, then brake lights stayed on all the time... turns out the "t" connector for the trailer harness under rear bumper was rotted inside...unplugged the 2 parts of the harness and pluged them into each other with out the "T" harness.... everything works great... Hope it helps ya

Ad
emissionwiz

Marvin

  • 85242 Answers
  • Posted on Aug 05, 2009

SOURCE: Misfires 96 gmc sierra 5.0

I suggest you have the injectors tested by the dealer, the sludge buildup will not cause a miss fire. to clean the throttle body use carberator spray while holding the engine idle high.

ZJLimited

ZJ Limited

  • 17989 Answers
  • Posted on Mar 31, 2010

SOURCE: Where can I find the diagram for a 1992 GMC Sierra

The GMC 1500 Sierra have several engine sizes, hope this helped...

1992 GMC C 1500 P/U 2WD 4.3 liter V-6 VIN "Z"

d9ffbf1.gif



1992 GMC C 1500 P/U 2WD 5.0 liter V-8 VIN "H"

6e77604.gif



1992 GMC C 1500 P/U 2WD 5.7 liter V-8 VIN "K"

18df209.gif


Good luck, and remember rated this. TY for using Fixya.

Anonymous

  • 15 Answers
  • Posted on Apr 30, 2010

SOURCE: 1996 GMC Sierra 1500 XC 4x4 5.7 Hard To Start

It is probably the fuel pump. If I remember the number correctly, this fuel system needs about 50 lbs to open a valve.
Until this valve opens, no fuel gets to the fuel nozzels.

Anonymous

  • 121 Answers
  • Posted on Oct 19, 2010

SOURCE: How to remove and replace the blower motor on a

If you look under pasenger side dash at floor board you will see blower housing. unbolt it and you may have to remove one dash bolt at bottom pry dash out a little and remove motor

Testimonial: "Thank you for your help."

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

Cant get no fire/replaced distributor /cap and roter replaced crank sensor and coil put wires and plugs { and still cant get fire to distributor} 1996 gmc/1500 5.7liter

if i understand u correctly u replaced the distributor and cap if so i would start with making sure my pick up coil was installed correctlyand or replace it.i also would look at the possibility of it being a powertrain control module or neutral safety switch if this vehicle is equipt with one. hope ive been helpful
0helpful
1answer

Have to replace distributor cap and button every 7 or 8 months. gets corroded inside and starts running rough.can i put a different. dist. on? aftermarket or something like that.

well you could put an accel cap rotor but there was a gasket on they car when it was new some are seprate gaskets and some are on the coil pickup if you cant find the gasket next time you change them just add some permatex around it
8helpful
1answer

I need the firing order of 1996 gmc engine sierra 5.7liter vortec

For the 1996 GMC SIERRA with 5.7L V8:

Firing Order:
1-8-4-3-6-5-7-2

Cylinders:
.........(back).........
|...8...|........|...7...|
|...6...|........|...5...|
|...4...|........|...3...|
|...2...|........|...1...|
.........(front)

Distributor Connections:
............(back)
Coil--->o
6------->o........o<-------5
4------->o........o<-------3
2------->o........o<-------7
8------->o........o<-------1
.............(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
0helpful
1answer

1990 gmc sierra(v6,4.3)starts but cuts off after running for about 2 min. replaced fuel pump and relay. could it be the distributor?

Is this an HEI distributor (large cap with coil on top) or a small module type distributor? I am going to lean towards the small module type, if this is the case the modules are known to have issues, remove the cap and check the harness connnection if it is tight then its probably the module. Remove the rotor, and remove the screws that hold it down, when you install the new module MAKE SURE you put some dielectric grease on the module that goes to the distributor as these modules do get hot and you need to dissipate the heat....... hope that helps
0helpful
1answer

I have a 1996 GmC sierra with the 350 in it. The

Check the distributor cap. If it is corroded, any condensation may make it not start.
0helpful
1answer

In what order do yu arrange the plug wires on the distributor cap or a 1990 gmc 350

1-8-4-3-6-5-7-2 Distributor turns clockwise Number one should be in the 5 oclock position. You should be able to draw an imaginary straight line between the coil tower and number one tower on the cap and the number one spark plug.
0helpful
1answer

1996 gmc sierra not firing when weather is damp replaced distributor and cap rotorbutton

try changing the spark plugs and spark plug wires that may help...but first to be sure try following the ignition system from top to bottom...first try holding a spark plug wire half an inch away from your engine block and let somebody else try cranking the engine if you can't see a spark then try that with the wire connecting the coil with the distributor if there is still no spark than the coil needs to be changed
Not finding what you are looking for?

86 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...