20 Most Recent 2006 GMC Sierra 3500 Questions & Answers

P0087 GMC - Fuel Rail Pressure Malfunction Pressure Too Low Possible causes - Faulty fuel pump - Blocked fuel filter - Faulty fuel pressure sensor - Fuel pressure sensor harness is open or shorted - Fuel pressure sensor electrical circuit poor connection - Faulty Fuel injector

hello u'd need a proper manual for this in my opinion like there are plenty of dealers and online shops that deal in those.. you can get some free at reliable-store and it;s actually really illustrative

Steering Column Trim Cover Replacement Important: You must check for 2 pan head tapping screws (1,2) in the lower trim cover before removal. If necessary, remove the 2 pan head tapping screws (1,2) from the lower trim cover (3). Remove the lower trim cover (3). If screws are not present in the lower trim cover, proceed to the next step. Gently unsnap the lower trim cover from the upper trim cover. Important: You must check for 1 TORX® head screw (1) in the upper trim cover (2) before removal. If necessary, remove 1 TORX® head screw (1) from the upper trim cover (2). If a screw is not present, remove the upper trim cover (2).

Do you have an after market programmer installed .what code is it showing .

HelloThe engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM and TCM (Power Train Control Module, Transmission Control Module). When a problem like this or other drive-ability related problems occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

turn key on do not start wait 10 sec then push down on brake and gas pedle for 10 sec done If you need further help, I’m available over the phone at https://www.6ya.com/expert/mike_9693b5ad75773352

could be some bad injectors...does it smoke real bad?

No real tricks, they're just really stuck. try twisting the boot and shield with pliers while pulling. They are surprisingly tough.

Remove the wheels
Stick a punch or something sturdy in a rotor cooling hole so it jams against the caliper. Loosen the 8 nuts that can be accessed through the 8 holes in the hub flange.
Remove the calipers from the knuckles and hang them from something other than the brake hose.
Remove the previously loosened 8 rotor nuts.
Tap the rotor with a hammer and it should fall off.

none, all front end parts should allow no play

Look under the left side of the vehicle along the frame rail. Follow the cable from the rear wheel toward the front. There should be a device attached to the cable. Tightening the bolt will remove slack from the cable

drivers side second cylinder from the front... 2468 on left side

gm has had alot of problems with there instrument cluster of the last few years best bet it to take to your local dealer they proubley can fix under warranty or goodwill it to u they put a new cluster in to fix thiem

Probable broken spring within the lock. Remove the door panel to access the lock. These things are held together with deformed tabs, but with a little grinding of the tabs, they can be pried apart. It might be easier to find another lock (new or used) instead of dealing with a pile of parts and a tensioned spring. The lock could be held together with a quick pass of a welder on each tab. Good luck!

Remove the passenger side inner fender. There should be 14 small plastic clips that hold it in place. Once you move the inner fender out of the way you will have unobstructed access and full view of the filter. This process should only take a few minutes and will save a lot of time and avoid a mess!

Get it scanned and properly repaired