How to replace headlight housing - 2005 Dodge Grand Caravan

Should be an adjuster screw on the back of the headlight

1. INSTALLATION GUIDE:
2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
3. Parts Identification:
4. Projector Headlight
5. Halo & L.E.D.
6. Bottom of the Headlight:
7. Ballast Bracket, Halo Wires(red/black)
8. Turn Signal Adaptor
9. TOOLS REQUIRE
10. 10mm - 8mm socket
11. Philip Screwdriver
12. Crimper/Pliers
13. For more information about how to install your vehicle, come visit our youtube page on
14. http://www.youtube.com/spyderauto
15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
21. STEP:
22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
24. Factory Xenon Headlight
25. Spyder Projector Headlight using Factory Xenon Lights
26. STEP:
29. PLS VOTE ME

BMW e46 HID Headlight Replace

Re: Replace headlight bulb

1. INSTALLATION GUIDE:
2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
3. Parts Identification:
4. Projector Headlight
5. Halo & L.E.D.
6. Bottom of the Headlight:
7. Ballast Bracket, Halo Wires(red/black)
8. Turn Signal Adaptor
9. TOOLS REQUIRE
10. 10mm - 8mm socket
11. Philip Screwdriver
12. Crimper/Pliers
13. For more information about how to install your vehicle, come visit our youtube page on
14. http://www.youtube.com/spyderauto
15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
21. STEP:
22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
24. Factory Xenon Headlight
25. Spyder Projector Headlight using Factory Xenon Lights
26. STEP:

BMW e46 HID Headlight Replace

To replace headlight bulb of kia pregio van: You only need Phillips screw driver and 10mm socket or open wrench. Open the hood, remove front grill with 4 phillips screw. This will give you room for your hand to pull out the headlight housing later on. Next is remove the signal light housing by unscrewing the phillips screw on top of the headlight housing then pull out the signal light housing and remove the bulb. You will see 2 pcs 10mm bolts on the side which hold the headlight. Loosened and remove the bolts on headlight holder then pull the headlight sideward. Remove power supply socket before removing it completely from the van. Remove bulb socket, spring clip, and busted bulb and replace with new one. Reassemble the disassembled parts in reverse order. That's it, will take you only 10 minutes.

1. Openthe hood of your Lexus and remove the power connector from the back of theheadlight. Press down on the release tab on the top of the connector and pullit off from the headlight. 2. Rotatethe headlight collar counterclockwise and pull it out of the housing assembly. 3. Inserta new headlight into the housing and rotate the headlight clockwise to secureit to the housing. 4. Plugthe power connector back into the headlight.

Step 1 Open the hood of your Beetle and look between the first two fender-mounting bolts. Then, look down a few inches from there. There is a small knob, which is the release knob for the headlight-housing assembly.

Step 2 Push the release knob down and then all the way up as far as it will go.

Step 3 Push the headlight housing forward from the back of the housing.

Step 4 Unplug the headlight connector from the back of the headlight.

Step 5 Push down on the plastic tab on the back of the headlight housing and slide the black plastic cover down to reveal the headlight.

Step 6 Remove the spring clip from the back of the headlight by pulling it off with your fingers. The headlight bulb will come out of the back of the headlight housing when you do this.

Step 7 Install the new headlight bulb and replace the spring clip to secure the headlight to the housing. Installation of the removed components is the reverse of removal.

From the engine compartment, unlock the 3 tabs that are over the headlight housing area. Remove the cover and unscrew the plastic ring that has the wires protruding from it. Carefully pulls the light fixture out of the housing. Pull the 2 L-shaped tabs up and remove the lens section. Reverse the steps to re-install the headlight. If replacing the full turn signal housing, unscrew 2 screws from each light , disconnect bulb wiring and remove. Replace accordingly.

Obviously the furst thing you need to make sure you have are the replacement lights

Step 1 Open the hood and unplug the HID power connector from the back of the headlight assembly

Step 2 Pull the protective rubber boot off the headlight housing.

Step 3 Squeeze the tabs on the wire clip that holds the headlight in place.

Step 4 Pull the headlight out of the back of the headlight housing assembly.

Step 5 Insert a new headlight.

Step 6 Secure the headlight with the factory wire clip.

Step 7 Replace the rubber boot.

Step 8 Plug the HID electrical connector back into the headlight.

1. Open the hood of your KIA Amanti and look behind the headlight that has gone out. Locate the round knob on the back of the headlight.
   
2. Turn the knob counterclockwise 1/4 of a turn and gently remove it from the back of the headlight. Carefully remove the electrical cable within the headlight housing that is attached to the back of the headlight bulb.
   
3. Locate the metal clip that holds the light bulb in place by pushing the clip arm straight in and sliding it down. Remove the bulb from the headlight housing.
   
4. Replace the old headlight bulb with new bulb. Secure it by sliding the metal clip up to hold the bulb in place. Reattach the electrical cable and replace the round knob to the back of the headlight housing.
   
5. Turn on the headlights to verify that they are in working order.
   

If you are replacing the headlight bulbs, rotate the bulb retaining lock ring counter-clockwise, pull retainer out of headlight housing and disconnect electrical connector. On the drivers side, you have to remove the fuse and relay box screws and move the box to the side to access the headlight bulb. If you are replacing the headlight housings, there is a push pin and 2 screws on the inside, behind the hood and one screw on the outside at the bottom. Remove these and pull the housing out enough to remove the bulb retainers.