How do i reset the computer after replacing the shift solenoid

Question edited for a lot more clarity, spelling 'silinoid' and others.

You need a transmission specialist with a pro grade scan tool computer to diagnose why. Shift solenoids, PCM or communication problems. You can't fix this stuff by guesswork, it is electronics.

Corrupt adaptive shift memory. Try clear and relearn.

https://youtu.be/jWMliD_3s3o

The check engine light does not come on when you turn the key on ,burnt bulb ? Did it before you replaced the shift solenoid ? I think it's the computer, How can I tell? Hooking up a scan tool to see if it communicates . Replaced which shift solenoid ? Was there a DTC - diagnostic trouble code ?
Is there B+ voltage to the coil pack ? VT/BK wire .
Good power an grounds to the PCM ?

DO A COMPUTER SCAN TO SEE IF YOU HAVE CODES. YOU MAY NEED TO RESET THE ECM PARAMETERS AFTER REPLACING THE SOLENOIDS BECAUSE IT MAY STILL BE IN DEFAULT MODE. I ASSUME YOU HAVE ALREADY CHECKED THE FLUID LEVEL

yes you can have just the bad shift solenoids replaced . you do not need to replace the transmission

LOOK FOR TRANSMISSION FUSE UNDER THE HOOD IN THE FUSE AND RELAY BOX.HAVE VECHICLE CODE SCANNED FIRST TO SEE WHAT TRANSMISSION SHIFT SOLENOID BAD.GUESSING WILL COST YOU.SOME TRANSMISSION SHIFT SOLENOIDS COST $70.00 TO $80.00 BUCKS.

P0753 Shift Solenoid A Electrical its inside of transmission not very easy to replace it controls the shifting of the transmission
P0763 Shift Solenoid C Electrical its another transmission shift solenoid
P0758 Shift Solenoid B Electrical another shift solenoid now my question to you is your transmission shifting normal have you had any work done to your car recently like changeing any seals on your transmission to have theses replaced by a mechanic its gonna be very expensive i could tell you step by step how to change them with theses codes you should be haveing serious shifting issues if you dont have shifting issues reset codes and see if they come back if they do then it could be in the wireing harness comeing from transmission hope this answers your question happy holidays

If I am not mistaken isn't that a shift solenoid code. If it is a shift solenoid code you will need to service the tranny and have it replaced. You can also check and see it there are any service bulletins or recalls on the tranny system through your local dealer.

What was the codes exactly that Auto Zone gave you.??? it might just be a simple wire harness that may have gone loose since you did some work on the speed sensor.
Here are the trouble codes for your car.  Good Luck and get the car scanned again for a more define information.

P0751 Shift Solenoid A Performance or Stuck Off

P0752 Shift Solenoid A Stuck On

P0753 Shift Solenoid A Electrical

P0754 Shift Solenoid A Intermittent

P0755 Shift Solenoid B Malfunction

P0756 Shift Solenoid B Performance or Stuck Off

P0757 Shift Solenoid B Stuck On

P0758 Shift Solenoid B Electrical

P0759 Shift Solenoid B Intermittent

P0760 Shift Solenoid C Malfunction

P0761 Shift Solenoid C Performance or Stuck Off

P0762 Shift Solenoid C Stuck On

P0763 Shift Solenoid C Electrical

P0764 Shift Solenoid C Intermittent

P0765 Shift Solenoid D Malfunction

P0766 Shift Solenoid D Performance or Stuck Off

P0767 Shift Solenoid D Stuck On

P0768 Shift Solenoid D Electrical

P0769 Shift Solenoid D Intermittent

P0770 Shift Solenoid E Malfunction

P0771 Shift Solenoid E Performance or Stuck Off

P0772 Shift Solenoid E Stuck On

P0773 Shift Solenoid E Electrical

P0774 Shift Solenoid E Intermittent

P0780 Shift Malfunction

Sounds like you need the updated engine computer for harsh shifting. Look up under the glove box at the computer. Number should be 89661-02K21 if not, you need the update. It is an 8/80 warranty item.