2009 Mazda MAZDA6 Logo

Related Topics:

A
Anonymous Posted on Sep 19, 2012
Be the first to answer

I have a Mazda 6 2009 with advanced keyless ignition. I am not getting any response when I push the start button or when I put in the auxillary key and push the start button. I don't think the battery is dead, so any advice?

Answer This Question

4 Related Answers

david dixon

  • 740 Answers
  • Posted on Jan 05, 2010

SOURCE: dead battery cannot open car door with key - 2000 mazda mellenia

this is a common problem with only using a key fob to get in.you should use the key once in a while to keep it free and operational.

spray some W-D40 in the key hole let it sit for a little while the try to put the key in the door and turn it back and foward untill it starts to move this may take a few minutes or 15min to unlock it but alittle bit of patience and tired fingers and hands and you'll be in.(after you get the lock free try using the key more often to save your self the head ache down the road)

Ad

Anonymous

  • 69 Answers
  • Posted on Dec 18, 2010

SOURCE: 1999 Mazda Millennia S - My keyless remote stopped

If the dash lights are not turning on, then it's probably a bad battery or battery connection. Also check the fuses. Hope this helps :)

Anonymous

  • 97 Answers
  • Posted on Mar 01, 2011

SOURCE: I have mazda 3 hatchback

since car is starting from pushing i would imagine it could be the starter motor... just a thought. also if thats not the problem maybe a wire has come loose (this isunlikely but possible) hope this helps?

Anonymous

  • 2418 Answers
  • Posted on Sep 10, 2011

SOURCE: My mazda 6 2.3L wont

This is an indication that you have a bad or loose connection at the battery. Check the cable ends on the battery and clean them of any green looking stuff. Make sure all connection are tight at the battery.

Testimonial: "Wow you were 100% correct. awsome... the cables were corroded from the terminals about 7 inches through my positives and negative. appreciate it boss."

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

I have lost my smart remote key for my Mazda CX-9 2011. Can I program a new one myself?
You may need 2 keys to do this, possibly just one. My source does not specify if 1 key will work but here is the procedure i found
With two programmed advanced keys
  1. Bring the programmed advanced keys (2) and a unprogrammed advanced key into the vehicle.
  2. Close all doors.
  3. Insert the supplementary key into the ignition key cylinder. NOTE:
  • Complete the procedures up to Step 7 within 30 s after the supplementary key is inserted.
  1. Turn the ignition switch to the ON position.
  2. Press the UNLOCK button on advanced key 1.
  3. Press the UNLOCK button on advanced key 2.
  4. From the ignition switch in the ON position, switch the ignition switch in the order indicated below.
  • ACC->ON->ACC->ON->ACC->ON
  1. Open the driver-side front door, press the door switch twice , and then close the door. NOTE:
  • After Step 3 is completed and the advanced key programming mode is activated, the door lock actuator operates to lock, and then operates to unlock.
  • If the door lock actuator does not operate, repeat the procedure from Step 2.
  1. Press the UNLOCK button on the unprogrammed advanced key twice . NOTE:
  • After Step 8 is completed and the advanced key is programmed, the door lock actuator operates to lock, and then operates to unlock.
  1. If programming more advanced keys, remove the supplementary key once, and then repeat the procedure from Step 2.
Read full answer
Aug 04, 2016 • 2011 Mazda CX-9
0helpful
1answer

Central locking sometimes works/not works, this is in last few days. Has push button ignition but last few days it won't even turn over and the push button area turns red along with the right hand side...
Make sure your battery cables are tight, even the smaller wires to the hot side. Maybe a keyless entry transponder battery has gone dead or usually a disconnected wiring plug. Read your error codes if there are any to see what connector plug it might be. Usually happens after accident, off road incident, flood or body work.
Read full answer
Mar 27, 2015 • Mazda Cars & Trucks
0helpful
1answer

How do I program a transponder key for Mazda6
You will have to take the vehicle to a Mazda agent and ask them to program a transponder key for your car. Every key is specially programmed for a particular vehicle according to its VIN number.
Read full answer
Oct 21, 2014 • 2009 Mazda MAZDA6
1helpful
2answers

Ignition key wont come out
Hi, we had the same thing happen, for us the ignition barell had "collapsed" internally holding the key in place - you might be able release the key by hitting the underside of the steering column while trying to extract the key - however it sounds like a replacement will be needed, due to the age of the car you should be able to source one from a car wreckers cheaply, make sure you get the keys with the new barrell.
Read full answer
Jun 17, 2014 • 1989 Ford Festiva
1helpful
1answer

Keyless ignition
You need to have the system reset by the dealer.
Read full answer
Sep 11, 2013 • Mazda Cars & Trucks
4helpful
1answer

Keyless entry not working
Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. Remove key from ignition switch. Close all doors. Open driver's door. Carry out the following within 24 seconds: Turn ignition switch ON and back to LOCK position 3 times. Remove key. Press and release driver's door courtesy light switch 3 times. Ensure doors lock and unlock. If not, wait 40 seconds and repeat procedure starting with driver's door already open. Press each remote control lock or unlock button twice. Ensure doors lock and unlock after each remote control operation. If not, proceed as follows: Press and release driver's door courtesy light switch once. Ensure doors lock and unlock twice. Repeat procedure starting with driver's door already open.
NOTE: A maximum of 3 remote controls can be programmed.
Read full answer
Mar 29, 2010 • 2004 Mazda 6
0helpful
1answer

Purchased a new clicker.from g/m.i can't program it.i have replaced the transformer under the dash panel that was used.. i have been told 96 models has several transmitters on it.
1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.
Read full answer
Jan 23, 2010 • 1996 Chevrolet Corvette
2helpful
1answer

2000chevy malibu keyless entry problem need help
1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.
Read full answer
Sep 22, 2009 • 2000 Chevrolet Malibu
0helpful
1answer

2008 altima When I place my key in the ignition(keyless entry) a warning shows "no key". I have changed the battery and it still says "no key" please give me an estimate of what you think it is and if it...
Lock your car with the keyless entry.Push it twice.Then walk over to passenger side and un lock with key.Then put key in ignition and start the car..If that dont work lock the doors again with the keyless entry.Push lock twice and then push the unlock twice..that should start your car,Repost if you have no luck to consider different stratigies.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

Read full answer
Apr 03, 2009 • 2005 Nissan Altima
9helpful
1answer

Keyless reprogram
resychronizing the key works.

1. Insert key into ignition and turn to
position 2.
2. Remove key and hold down lock button
while pushing unlock button five times.
3. Release all buttons, then push either lock or
unlock button.
!!!!!!!!!!!!!Procedure must be completed within10
seconds.!!!!!!!!!!!!!!!!!!!
Read full answer
Oct 06, 2008 • 2001 Mercedes-Benz M-Class
Not finding what you are looking for?

View Most Popular

2009 MAZDA6

  • Cars & Trucks

Related Question

I have lost my smart remote key for my Mazda CX-9 2011. Can I program a new one myself?

  • 2011 Mazda CX-9

791 views

Ask a Question

Usually answered in minutes!

Popular Questions

CHECK ENGINE CODE P2187 SAYS

2003 Mazda Mazda6

FIRING ORDER FOR MAZDA 6 3.0LITER

2003 Mazda Mazda6

Mazda 6 immobiliser light flashing

2006 Mazda 6

Mazda 6 2.0 136bhp diesel stalls all the time on tick over.

2006 Mazda 6

How do you replace the head light bulb on a 2004 Mazda 6?

2004 Mazda 6

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
2009_mazda6_om_eng.pdf....

2009 MAZDA6

Loading...