20 Most Recent 2006 Chevrolet Venture Questions & Answers

The throttle body needs a thorough cleaning. Brake clean and a toothbrush will do the job. Clean the back of the throttle plate as best you can.

might be plugged fuel filter or maybe idle air control valve or severely plugged air filter

you did not say if this is in the front or rear but no matter your brake hoses can colapse inside they let the fluid go towards caliper but not return

Ignition Switch (2005 Chevrolet Venture listed but the 2006 Venture was not) Removal & Installation To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • The SIR system
   • The upper and lower trim covers
     
     
   • The wiring harness assembly (D) from the wire harness strap (E)
   • The wiring harness straps (C) from the wire harness assembly (D)
   • The wiring harness strap (B) from the upper tilt head assembly (A)
     
     
   • The turn signal switch assembly connectors (B) out from the bulk head connector (A)
     
     
   • The PASSKEY III (B) off of the ignition lock cylinder case (A)
     
     
   • The key alarm connector (A) from the ignition lock cylinder case (B)
   • The 2 tapping screws from the ignition switch assembly (C)

To Install:

1. Install or connect the following:
   • The ignition switch assembly (C) onto the ignition lock cylinder case (B)
   • Two tapping screws into the cylinder case.
     1. Torque to: 42 inch lbs. (4.7 Nm)
   • The key alarm connector (A) into the ignition lock cylinder case (B)
   • The PASSKEYS III (B) onto the ignition lock cylinder case (A)
   • The turn signal switch assembly connectors (B) to the bulkhead connector (A)
   • The wiring harness assembly (D) into the wiring harness strap (E)
   • The wiring harness strap (B) into the steering column tilt head assembly (A)
   • The wiring harness straps (C) onto the wire harness assembly (D)
   • The upper and lower trim covers
   • The SIR system

it could be a heat sensor bud thats it

while they are similar they cannot be interchanged. all the sensors and computer are different. i also believe the mount locations are different.

IT REALLY SOUNDS LIKE A HEAD GASKET AS FAR AS ABS IT COULD BE LOW ON BRAKE FLUILD OR BRAKES MAY NEED REPLACED OR ABS MODULE VERY DANGEROUS TO DRIVE WITH ABS LIGHT ON

Question edited to fix Fixya redacting a word it doesn't like. Question moved from Misc to model category. https://www.google.com/search?q=fix+the+petcock+on+Chevy+Venture ,,

It is on the fuel pressure regulator https://troubleshootmyvehicle.com/gm/3.8L/how-to-test-the-fuel-pump-1 https://www.2carpros.com/questions/chevrolet-venture-2000-chevy-venture-fuel-pressure-regulator--2 ..

get a gas cap their cheap

Its a long way from the gas tank to the engine so you need a fair bit of cranking. Also, if it ran dry, it means the pump also was running dry after it stopped. The gas lubricates and cools the pump, so you may have wrecked it. First thing, check that fuel is being pumped. Then check the pressure.

Before you start cutting wires it is worth you contacting the company who supplied the mirror unit and get them to recheck the one they sent you. 2005 was the last year they made the Venture BUT the LT trim level ended in 2004. They might have sent you the mirror for a vehicle that isn't for the LT trim.

Some fixya user told me a website reliablestore it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go there and try

hello u will find a lot of wiring diagrams and circuit diagrams help books and stuff like this at reliable-store the girl in the chat box can help u instantly... im a frequent buyer there since Im a mechanic so take help from there

you can try out some guide from here reliable-store they also provide live chat fe ature for instant help and it's very useful

Hi have you had any joy finding fault I have the same problem with my Maxus. I've replaced endless stuff even main pump ,narrowed it down to crank position sensor.but sensor is fine there should be a 5v feed but there isn't one ,checked wire back to ecu and its ok. But carnt see it being fault on ecu van drives and performs great once running. Seems to be quite a common thing on these but no one seems to have an answer, if you have any joy with yours or need any questions over it you can contact me on [email protected] for number , cheers dave

I believe it is a electric hydraulic system so maybe a bad switch or wire or hydraulics could be getting varnished and sticking