20 Most Recent 1994 Dodge Grand Caravan - Page 8 Questions & Answers

should be under warrenty take it to the dealer

There could be several reasons why your 2007 Dodge Grand Caravan sliding door is not latching properly. Here are some possible causes:

1. Obstruction in the Door Track: Check the door track for any debris, dirt, or foreign objects that may be blocking the door from closing fully. Clean the track and remove any obstructions.
2. Broken or Misaligned Door Hinges: If the door hinges are damaged or misaligned, the door may not close properly. Inspect the hinges for any signs of damage or wear and replace them if necessary.
3. Damaged Latch or Actuator: The latch or actuator that holds the door in place may be damaged or malfunctioning, preventing the door from closing properly. Inspect the latch and actuator for any signs of damage and replace them if necessary.
4. Dead Battery: If the battery in your Dodge Grand Caravan is weak or dead, the electronic functions of the sliding door may not work properly. Check the battery and replace it if necessary.
5. Faulty Door Control Module: The sliding door may be controlled by a door control module, which may be faulty or damaged. Have the control module tested and replaced if necessary.

In any case, it's recommended that you take your vehicle to a certified mechanic or dealership to diagnose and fix the issue, especially if you are unable to get the door closed manually.

limited info generic answer check for correctly installed --out of adjustment --needs bleeding

fails ON BLOWER HIGH? No year car told so answers are generic.) answer for blower dead on high and silent,. too, well that is easy, in order of easy to find or fix or common or test.

1. fuse blown blower.
2. blower motor bad. (12vdc there blower is bad) or?
3. blower jammed, some cars mice can get here and nest . or insects.
4. blower controller dead.
5. if blower fails only below HIGH the resistor block is bad.

tests are easy, but need a voltmeter to avoid GUE$$ing. no year car told not told if controls are marked, DEGREES TEMP.> (called climate controls) the manual controls not temp number just cool to hot.

engine starts and runs and drives and is OK??????????all else works? head lamps work key off and on?, parking lamps 4corners, TURN sigs,brake lamps , wipers, best it tell what works and does not work on any electrical fail post, scan the car is first if fuses test good;.PCI to voltmeter cluster is PCI data.PRNDL cluster status is PCI data even the radio is PCI connected so if wired wrong OOPS> PCI dies.rtmread the service manual see all wiring there.https://eautorepair.net/Marketing/Default.aspFUSES ARE FIRST, <<< repeat 3 times.fuse 14,19,20,24 , BCM has 4.14 is BCM memory fues, IOD.

Jim Workman The most likely reason would be loose or broken exhaust mountings. This question you resurrected is from 2014!

ALL CARS MADE (60'S UP?) DO NOT CRANK AT ALL IF THE PRNDL (P/N, OR TRS , RS) SWITCH FAILS SO MOM DOES NOT DRIVE OVER THE KIDS. by law too. even a new battery must be charged up seems the key switch is hacked up or last owner had 25lb key ring and wrecked it easy.. battery dischareged 4 lugs on battery cables, loose or rusty lugs. fuse blown. PRNDL switch is bad, or wires to it cut. ignition switch bad. use a schematic and voltmeter to find where t fails. easy. use a meter. no engine told size. seem to me key switch is bad so replace it. (no IMMO on car)

I would take it back to the dealer under warranty.

Well, those are classic symptoms of bad engine timing, so I'd have that checked. Maybe your timing belt has jumped a tooth. Be careful with that starter fluid, you could blow yourself up.

https://ibb.co/fCgJJkB The relay should be in the integrated power module, under the hood. Click on the link, wiper diagram. The relays may be soldered into the fuse box.

Question edited for clarity. Here is the parts schematic https://www.moparpartsgiant.com/parts-list/2018-dodge-grand_caravan/doors_door_mirrors_and_related_parts/sliding_door_hardware_components.html https://www.google.com/search?q=2018+dodge+grand+caravan+sliding+door+parts ..

You need someone with a Pro Grade Scan Tool Computer to find out what the issue is with the ECU? You can reset all the codes by disconnecting the battery for 10 minutes and see if they come back. The first link in here says the ABS Module is bad. https://www.google.com/search?q=scan+tool+says+11+ECU+internal+circuit+failure ..

Question edited to what I think you meant to say. This is a job for the professionals, normally a trailer and hitch place. If it is the Bruno lift, it should have come with an installation manual. If not, you can contact them direct and ask. https://www.bruno.com/scooter-lifts/curb-sider https://www.google.com/search?q=install+curb+sider+in+Dodge+grand+caravan ..

if you cleared the code - fixed arc and checked their are no more arcs - and keeps coming back then problem can be a burnt or carboned valve --lifter -push rod --piston

Latch hook needs to be replaced. Some use rubber coating to dampen rattle. Yours may have worn out. check flushness of door to main bodyline. Sometimes the door is latched but there is some gap between door sill and door. If that is the case, the latch hook needs to be repositioned towards the inside.

Hello
Many times this problem is caused by the coiled flat ribbon contact that is located under the steering wheel, it looks like a Clock-Spring if you were to take it apart, it is contained inside a plastic flat round enclosure . Also make sure you have properly functioning brake lights, they can keep the cruise from coming on as well. If the brake lights check ok then the clock spring-contact contact may be the problem, one of the contact filament's is broken and the connection to the steering wheel switches of the Cruise has been lost. In order to replace this contact you must disarm the airbag system.
At the link below is a instructional video on YouTube of how to replace the Clock-Spring rotating contact in a Chrysler product Mini Van.

check fuse #12(small 10 amp) in the fuse box in the drivers side dash. If it has blown out, the scanner cant read the obd.

Here is a post with a video that should help you. https://www.pacificaforums.com/forum/505-child-safety-car-seats/3866-remove-headrests-2nd-row.html

Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything someone on fixya recommended it to me and I thank him even today They have full manuals and it's verrrrry cheap and mine I got free in offers 3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins there is one website more but i don't remember its name it was 2 years back bitman something link this Try these out brother

Pulling the floor onsoles are super easy, just identify whi h ones lay on top of the other..just a bunch of screws, starting inside an opened console. Snap them back in place in reverse order.