Top 20 2005 Nissan Almera Tino - Page 4 Questions & Answers

Indicates an error with your 'Smart Key'.Either your key is not being detected at all, or there is a code mismatch. You made need to change the FOB battery.Contact your local Nissan dealership, as these issues are rather finicky and usually require their electronic computer hook-up to diagnose.

sounds like a bad axle shaft

That's is the brain box

We do not have this model in the USA so we have no info on it. Sorry

how to fit

It can be repaired but it all comes down to cost, call around some instrument repair companies and see what the quote, you may find a cheaper one in a wrecked car or the dealer may be able to supply a replacement.

I have not used my nissan micra 2003 for 7 months it has been stored in the garage but the engine has been started on a weekly basis but today the warning engine light has come on, the car has only done 2300 miles, SHOULD I BE WORRIED or is it because the battery has been disconnected in between starting the engine so it didnt drain the battery while it was standing in the garage unused, this has happened the day before i take it for a mot.....

Has the Throttle body been removed and cleaned thoroughly both sides? Was a Throttle body relearn done afterwards. https://www.google.com/search?q=2018+Nissan+NP200+8v.+Throttle+body+problem Ideally you need an auto electrician to check for Diagnostic Trouble Codes and do a full system scan with a pro grade scan tool computer. It can also do the relearn and check the IAC. https://www.google.com/search?q=auto+electrician+near+me ....

no car told, maker, model , year and engine optionno countryl told . wow,not told does the starter crank the engine over fast.that is first, or it will never start or run.cranking is first.check all fuses.?vast Nissan cars and trucks are sold all over earth and are not the same. if it does crank the crank shaft pulley fast then if gas enginecheck for spark. next.fuel tests are last.my car can be started 3 waysKey cranked.push started (in 2nd gear manual transmission)or gravity started off a hill.so as you can see there are 3 ways to start some cars.my guess is it cranks fast.fuses gooddash Gauge not on "E"nobody put diesel in the GASOLINE tank or water there from ECO pranks.spark fails doing the 100 year old now, classic test, using test spark plug>fueling dead but instant start spray works for 3 seconds.watch scotty Khttps://www.youtube.com/watch?v=064Ilsz8Fzghttps://www.youtube.com/watch?v=064Ilsz8Fzg

Is this a new key as well? On a lot of modern vehicles the vehicle's electronics need to be told that there is a new ignition key and ignition barrel fitted. This will need to be done through the OBD connector under the dashboard. If it is not done the vehicle immobiliser won't turn off as it doesn't recognise the key you are using.

Question edited for clarity,, translated to written English and spelling corrected or 'indicators' After you replaced the battery, did you reset the security and immobilizer? The items you have problems with are all functions of the Body Control Module which is also the functions of security. Although it it is a stretch, that is the most likely as long as you have checked every fuse with a test meter that it is assigned those functions. You can do the the fuse testing very easily and quickly using the test points on the top of every blade fuse. Ultimately, you may need an auto electrician. https://www.google.com/search?q=auto+electrician+near+me

Nissan Navara (D22; 1997-2004) fuses and relays

Fuse Box Diagrams https://fuse-box.info > nissan > nissan-navara-d22-1997... It is located in the instrument panel, behind the protective cover. ..

This is not a model that we know in North America. Your local dealership will have one, or you can order online. This link should find sources near where you are. https://www.google.com/search?q=2000+Nissan+KA24DE+replacement+Vehicle+Speed+Sensor ..

Help in the link. I like to use a broader approach. Google year nissan model A14 mains and big end torque settings https://www.google.com/search?q=Torque+settings+for+nissan+A14+mains+and+big+end+bearings ..

There is no relay for the dash indicators. I'm assuming you're referring to the dashboard's instrument panel. There's a 10amp fuse for the instrument panel that you should check and/or replace. It's in location F11 of the fuse box, located in the vehicle on the driver's side. https://fuse-box.info/nissan/nissan-navara-d22-1997-2004-fuses-and-relay

Disabling a car alarm yourself can be tricky and might vary depending on the exact model year of your NP200. It's actually not recommended for safety reasons. Here's a safer route: contacting a Nissan dealership or a trusted mechanic. They'll have the proper tools and knowledge to handle your immobilizer issue and get you back on the road securely.

Does it go into 4th gear when the OD button shows activated? If it doesn't, sounds like a transmission issue. Possibly the torque converter. Have you connected an OBDII scan tool and attempted to pull any TCM codes? That may be helpful in pinpointing the issue, if there are any codes stored.

Taking out the steering box in a Nissan 1400 2007 pickup truck involves a few steps, and you do not need to remove the engine to access the steering box. Here is a general guide on how to remove the steering box:
1. **Disconnect the battery**: Always disconnect the battery before working on any components in the engine bay.
2. **Raise the front of the vehicle**: Use a jack to lift the front of the vehicle and secure it with jack stands for safety.
3. **Remove the wheels**: Take off the front wheels to access the steering components.
4. **Disconnect the steering column**: Inside the cabin, detach the steering column from the steering box.
5. **Disconnect the tie rod ends**: Remove the tie rod ends connected to the steering box.
6. **Remove the steering box mounting bolts**: Locate and remove the mounting bolts that hold the steering box in place

Question edited and turned around for clarity. Not enough coolant in the heater core. Have a read and follow these instructions carefully. https://www.fixya.com/support/r29872074-vehicle_cooling_system_no_heat They do have some 'history'. https://www.google.com/search?q=1996+Nissan+Largo+no+heat ..

I would check the heaters are working on the down stream sensor and ensure they are supplied and manufactured by Nissa.

To remove the starter motor on a 1994 Nissan Bluebird SSS 2 litre ATTESA-U13 engine (AWD), follow these steps: 1. Disconnect the negative terminal of the battery to prevent any electrical accidents. 2. Locate the starter motor, which is typically located near the transmission bell housing on the engine block. 3. Remove any heat shields or other components that may obstruct access to the starter motor. 4. Disconnect the electrical connections to the starter motor, including the wiring harness and solenoid. 5. Remove the mounting bolts that secure the starter motor to the engine block. 6. Carefully slide the starter motor out of its mounting position and set it aside. 7. Install the new starter motor by reversing the removal steps. As for finding a repair manual for your Nissan Bluebird SSS, you can try searching online for a digital version that you can download, or you can purchase a physical copy from a reputable auto parts store or online retailer. Additionally, you may also be able to find helpful information and step-by-step guides on online forums and websites dedicated to Nissan vehicles.