Energizer Camping, Backpacking & Hiking - Answered Questions & Fixed Issues
How to change lightbulb in hard case energizer flashlight?
Hello, Lori -
There is more than one style of Energizer Hard Case Flashlight.
- Professional Mult-Use Light
- Professional LED Task Light
- Spotlight
- Professional LED Inspection Light
- PivotPro Light
- LED Work Light
- LED Magnet Headlight
- Professional Rugged LED Headlight
Which one are you asking about?
Without knowing which model your question is about, I suggest you contact Energizer Customer Service and ask how to open your flashlight model to change the battery. This is the link to the Energizer Contact Us web page:
https://energizer.custhelp.com/
Best wishes.
7/1/2018 10:37:38 PM •
Energizer...
•
Answered
on Jul 01, 2018
•
2,767 views
How to connect a spring pole 6v battery
Inside the case of the light, there will be 1 wire with a tapered notched connector. Take the connector with the low end of the taper and push it into the negative (-) spring (in between the coils ) of the battery. The spring will wedge the connector it one of the notches and will hold it securely. Reattach the lense carefully seating the end of the bulb onto the positive (+) spring of the battery.
11/21/2016 6:22:04 AM •
Energizer...
•
Answered
on Nov 21, 2016
•
916 views
How to test a flashlight bulb
To test a flashlight bulb you use an Ohm meter which will detect a broken filament or an open circuit within the bulb. If the bulb is bad it will read "OL" if it's good it will read "00.0"
11/21/2016 6:12:16 AM •
Energizer...
•
Answered
on Nov 21, 2016
•
402 views
Manual for ML1W2AAE
You can get the data sheet with the flashlight information at
digchip.com Just type in the flashlight model number.
How to fix the switch on eveready lantern flashlight
The switch in the lantern is a press fit switch so you will destroy it when you remove it. Remove the lense and retainer ring. Remove the battery. With a pair of pliers, preferably channel lock water pump pliers crush the switch into small piece and discard. Trail Tech makes the exact water resistant switch model 040-ls-b and you can get it at Amazon or on eBay . The switch runs around $6.25 + $4.00 shipping
12/1/2016 3:39:41 AM •
Energizer...
•
Answered
on Dec 01, 2016
•
1,731 views
How do I Replace the batteries on Energizer ML1W2AAE
If you can remove the base, but the batteries will not slide out because of battery swelling or corrosion you can drill a small 1/8" hole in the battery base (negative end) about 1/4" deep. Get a
#10 sheet metal screw and slowly screw it into the bottom of the battery and pull it out. Be careful not to get any of the battery residue on you and if you do don't worry just wash it off. Do the same to the second battery, but use a longer screw.
11/21/2016 3:16:30 AM •
Energizer...
•
Answered
on Nov 21, 2016
•
336 views
Change the battery in the hard case
Start by unscrewing the lense cap retaining ring. Pinch and remove the clip from the negative (-) spring on the battery. Remove battery and slide new one in. Reconnect wire connector in between spring on the negative side of the battery. Note: some lanterns have a v'd plastic ear on the back of the reflector so when you go to screw the reflector back on, align the v'd ear with the plastic bar inside the case under the handle and slide it together until you can screw the retainer ring on.
11/21/2016 2:37:53 AM •
Energizer...
•
Answered
on Nov 21, 2016
•
521 views
Not finding what you are looking for?