How do you program a M7324 to work with the Handsfree feature?

For external numbers press FEATURE *1, then press the button you want to store the number on, then enter the phone number using the dialpad.
For internal numbers press FEATURE *2, then press the button you want to store the number on, then enter the extension number using the dialpad.
To determine what is currently programmed on a button, press FEATURE *0, then the button to identify and the display will show what feature or autodial number is programmed on the button. If the button is a line button or line pool button, you will not be able to clear it through user level button programming. System level programming must be accessed to change line appearances.

There is a speaker test you can do. Press the feature button then on the dial pad press 805 followed by the # key or the next key until you see speaker test in the display. Press the test key or the hold button to start the test. You should hear a page tone at maximum volume. Press any button to end the test, the volume will return to its previous level.

The phone is mute by pressing the handsfree/mute button(bottom left button). sometimes the button labels do not match the feature that is programmed for the button. Press feature * 0 and any button to see what feature is programmed on the button.

press feature ** 266344 then press your password enter terminals &sets then enter your extension number then navigate that extension until Capabilities then enter it and navigate until Handsfree and makes it auto.then HF answerback and make it Y

Sounds like the handsfree button might be stuck down. Try slightly pulling up on the button and see if that changes to the handset.

Programming is done on 7310, 7324 and 7316 type sets.Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you want to change to handsfree.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the show key (top right arrow) .
The display say foward no answer.
press the next key 3 times (bottom right arrow)..
The display should say handsfree. Press the show key.(top right arrow) change from none to auto
Press the release key when finished

To get handsfree working on any T7316 telephone you have to go into system programming to make sure full handsfree as been set to either Auto or Standard depending on software level of system you will get a choice but on latest version of software only option is for Auto, to check on telephone if handsfree as been programmed leave handset on phone press feature * 0 you will see key enquiry press a key in display, press the bottom intercom key on r/h/s of phone if it says extn number handsfree as not been programmed if it says handsfree mute you should be able to press handsfree key on phone to make or answer a call.

You need to reprogram the features to buttons. Try this:
Press "Feature*3", then press the button to be programmed, and enter the associated feature code (below).
Transfer - Feature 70
Call Park - Feature 74

Good Luck!

if the call log program was turned on in the system, you should be able to get into it by entering feature 812(call log). you can program a call log key by pressing feature*3 pressing the button you want to program call log on and entering feature 812.
hope that helps

Programming should be done from the M7310, M7324 or the T7316E set. Administration access code: Feature * * 2 3 6 4 6 which also is Feature * * A D M I N.
If asked for a password enter the same 2 3 6 4 6.

If that doesn't work you may have the newer Compact ICS or the Modulur 0x32 control unit wish will be Feature * * 8 4 6 3 which is T I M E. Password is 2 2 7 4 2 which is B A S I C or A D M I N which is 2 3 6 4 6.
When in programming just press the (next) button until you see what you want to change. Then press (show),then (change) if you want to change it. If you pass it, just press (back)
Example: To change the Time & Date Press (next) until you see Time & Date. Then (show) Then (change) Then (change) again, change it if you need to, Then (next) again until you see what you need to change. For example; only the hour needs to be changed for day light savings time. Just press (next) until you come to the (Hour). Then Change it. Then press release (RLs) when your done. To get out of programming, just press the release button (RLs).

Feature 71 isa link key. It generates a link signal(also known as hookflash, flash, recall, or tap). it can be programmed on your set by entering feature *3 pressing the button where its to be located and entering in feature 71.
I think thats all to know about a link key, hope that helps.