1995 GMC Yukon Logo
Posted on Oct 04, 2010

I have a 2002 Yukon Denali and I was wanted to know, how do u change the bulb in the steering wheel?

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 16 Answers
  • Posted on Oct 09, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Oct 09, 2010
Answers
16
Questions
0
Helped
6064
Points
40

Steering Wheel Control Switch Assembly Replacement Removal Procedure

  1. Remove the steering wheel. Refer to Steering Wheel Replacement .
    I have a 2002 Yukon - 399638.gif
    tif.gif
  2. Remove the horn switch from the steering wheel.

    tif.gif
  3. Remove the steering wheel shroud retaining screws from the back of the steering wheel.
  4. Remove the steeringI have a 2002 Yukon - 408596.gifoud from the steering wheel.
    I
    tif.gifI have a 2002 Yukon - 780085.gifi class="h_mi">Remove the steering wheel control switch mounting screws.

    tI have a 2002 Yukon - 408598.gifass=
  5. Disconnect the steering wheel contrI have a 2002 Yukon - tif.gifch (2) electrical connector (1).
    408598.gif
    tif.gif
  6. Remove the steering wheel control switch from the steering wheel.

Steering Wheel Replacement Tools Required J 1859-A Steering Wheel Puller
Removal Procedure
  1. Disable the supplemental inflatable restraint (SIR) system. Refer to Disabling the SIR System in SIR.
  2. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
  3. Remove the horn switch. Refer to Horn Switch Replacement - On Vehicle . I have a 2002 Yukon - 374820.gifs="h_mi">Make an alignment mark in order to note the relationship of the steeI have a 2002 Yukon - tif.gifeel to the steering shaft.
  4. Remove the steering wheel nut.
    374820.gif
    tif.gif
  5. Remove the steering wheel, using the J 1859-A .
Installation Procedure

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I drive 2002 yukon denali and was making a sharp turn when the front wheels lock. They wont turn, i finally got them to turn enough to back up out of the way. It looks like it has enough ps fluid

a broken CV or UJ on a drive shaft can cause the steering to lock up , jack up front end and check for damage to the drive shaft's rubber covers to the drive joints, push/pull wheels in and out , as in steering motion while spinning wheel and feel if there is anything restricting a smoth movement , hope this helps
0helpful
1answer

2003 yukon xl denali cranks but won't start

i agree first check if you got a spark and check if fuel is actually being supplied
0helpful
1answer

All but one light on my 2005 Yukon Denali steering wheel are out what could be the problem?

One possible area is the clock spring. This is a coiled ribbon wire, under the steering wheel, that allows the wheel to turn, and still have wires connected. Eventually the wire breaks at one point.
0helpful
1answer

Steering wheel is locked up. engine doesn"t start.

Are you saying that you are able to turn the ignition key but the steering wheel doesn't unlock, and the engine doesn't crank or is it that the key won't turn? Either way you have something broken, probably the ignition lock cylinder. The steering wheel has to be removed, There are quite a few special tools you have to have, you have to disable the air bag. It's not something you want to do yourself if your not sure what your doing.
0helpful
1answer

Want to reset the service engine light on a 2002 denali

OK, take an OBD-II scanner and press the erase codes button when connected to the OBD-II connector below the steering wheel under the dash board.
1helpful
1answer

I have a 2002 Denali pickup with quad-steer and the steering wheel is very hard to turn to the right. I have switched to 2 steer and have the same problem. Could it be the steer box or the pwr steering...

it should have a pump is there any whining noise when steering if so ad power steering fluid and check for leaks your owners manual will tell you what fluid and the pump will be on the front side of engine
0helpful
1answer

Rear wheel bearing is out, how easy to repair

not easy,you will probably need a hydraulic press to remove and reset the bearings
0helpful
1answer

Change lisence plate lights

Look where the wires go to the lights underneath. Grab the white rubber piece that goes into the light housing and twist 1/4 turn. Then pull. The bulb just pushes into its terminal in the white rubber.
Not finding what you are looking for?

959 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...