ERROR CODE "C6400" CALL SERVICE PERSON.
POWERED DOWN AND BACK UP. STILL SAME ERROR DISPLAYED. WHAT DOES THIS ERROR CODE REPRESENT.
THANKS. PABLO
Follw these steps, it should work
turn off copier.
open top toner cover.
turn copier back on.
when you see message "close top cover" press "system menu" button.
scroll up to "service setting" then press the # button, green "start" button and the "enter" button all at the same time.
then scroll down to "maint mode"
press "enter"
then enter 163
press" enter "
turn off copier then turn back on
close toner cover
you should be back in business
DEAR SIR,
why there is no maint mode here only transport mode
This Problem is a power supply problem and commonly occurs when you've had a power failure. 99.9% of the timer you don't need to have anything repaired or replaced, but what you do need to do is go into the machine's service mode and reset that code using service mode item U163.
Unfortunately I'm not at liberty to give you the procedure to get into the service mode... This is privelaged and confidential technical info. BUT, now that you know what to do to get rid of the problem, maybe you can get that info from somebody else.
Fuser unit wormup error but it happens mostly deu to power sure if the heater lamp themal fuse ,themoster and power suply is still ok test the lamp ,fuse with meter for continuty test themoster for oms after reset conect meter to powersuply outlet to the lamp u must just over 100v ac ,if not powersuply is falty.Corect reset switch off machine oppen cover were u put the toner in switch on machine show cover oppen go to service mode and execute u163 reset 'fixing error' switch off close cover and switch on now do the tests. Even before switch on have meter over lampcable black and white that exite power suply for 100v ac and over if it is that serious.
I found this for a KM-1500 which is just about the same machine.
http://www.copytechnet.com/forums/kyocera-mita-copystar/4440-c6400-error-km1500.html
J'ai un probleme avec ma photocopier kyocera MITA , KM 1510 qui affiche sur le tableau d'affichage un code error J 000 si vous pouvez me venir en aide SVP
merci bien
SIM 163 Reset (only do this one SIM, by doing others you could cause your machine to no longer function. Also see note at bottom.
Entering Simulation Mode
1. Press the system menu/counter key.
2. Select Service setting using the up/down cursor keys.
3. While pressing the start key and the # key, press the enter key. (Maintenance mode is entered.)
4. Select Maintenance mode using the up/down cursor keys.
5. Press the enter key.Enter the maintenance item (163 Resetting fuser problem) number using the up/down keys.
6. Go to step 1 under method below.
Resetting the fusing problem data Description
Resets the detection of a service call code indicating a problem in the fusing section.
When a service call concerning the fusing section occurs, turn the power switch off and open the front cover.
Then, turn the power switch on and press the system menu/counter key to enter the maintenance mode.
Method
1. Press the enter key. A selection item appears.
2. Select Execute using the up/down cursor keys.
3. Press the enter key. The fusing problem data is initialized. (Four service calls, namely C6000, C6020,C6050, and C6400 are reset.)
Completion
Press the back key. The indication for selecting a maintenance item No. appears.
Note: Sometimes in order to do the reset when the machine is in an error state you need to open the top cover (like to replace the toner) and leave it open until you have performed the reset.
13,897 views
Usually answered in minutes!
I cant find maint mode button to reset . where do I find it ?
I did have the same problem on a 1118MFP after a 21-2 hour blackout. Following both ottoman23 and KyoDoc 's suggestions, plus an extra scroll down after the last enter to "activate", then "enter", then turn off etc. Now all OK. I don't know how much $ I saved, but the work time is invaluable. CHEERS!
ERROR CODE "C6400" CALL SERVICE PERSON. I TRY TO SWITCH THE POWER BUT STILL THE MONITOR FLASH ERROR CODE "C6400" CALL SERVICE PEROSN
THE MONITOR FLASHED THIS "ERROR OCCURRED. CALL SERVICE PERSON.
my KM 1820 registers error code C6000. i followed the instructions posted by ottoman23 but won't work i press system menu but the red light still keeps on blinking and there is a t-*** sound. no change on the screen. it still registers close top cover. anybody please help. thanks. erizardo2000
@ottoman23:
wow. thanks. it really worked.
hi
I've tried your solution and now the error lite is blinking . cant get out of it what can I do
( also couldn't find maint mode button and thats why it got to start blinking. ) thanks
please contact your technical representative
when i switch on my copier, it indicates C-6400
codigo de error c6400
×