Kyocera Office Equipment & Supplies - Recent Questions, Troubleshooting & Support

The problem is occurring when you make a copy or a print, like a status page?
If it is a copy then you have to clean all the mirrors in the scanner unit.
If it is a print (no scanner intervention) then check the developer unit and the the transfer roller, mostly the first one.

Kyocera Office... | Answered Yesterday

The message you get is from the fuser setting for printing envelope. At the back of the printer, you have a handle wich opens the back dor. There is located the fuser (fixing unit) that will slide back. On left and right of the fuser, you can see 2 green buttons. In your case one of them or both are pressed. If you press one time, the button goes down. If you press again, the buton rise up. Try to press them down.

Kyocera FS2020D... | Answered 2 days ago

your scanner may get stuck to railing

Kyocera Copystar... | Answered on Jan 18, 2019

Description BD steady-state problem ASIC detects a BD error A for 2 s after the polygon motor rotation has been stabilized. Causes Poor contact in the connector terminals. Defective laser scanner unit. Defective engine PWB. Remedy Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. Defective laser scanner unit. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation.

Kyocera Office... | Answered on Jan 16, 2019

I am living in a Pakistan Village and have cyocera K-6030. I am facing an error on control pannel C3300, I would be most grateful, if I may be informed only that in which part of the machine this fault of C3300 is? it solution please. Thanks with regards. my e mail no is and If some one here can show me its solution, because my e mail is also not opening. thanks. my name is ghulam muuhammad

Kyocera Km-6030... | Answered on Jan 16, 2019

theres a sercive manual on this page as pdf format,hope it helps

Error Codes Kyocera Mita KM5050 Code C4200

Kyocera Office... | Answered on Jan 16, 2019

take off the cover and wipe down all edges of surface where it fits with an acohol wipe. Not enough mpoisture to screw it up but it should get pretty much everything

Kyocera Office... | Answered on Jan 12, 2019

there are many many factory modifications/bulletins for that machine, really the tru fix is very time consuming and if you are paying a dealership to repair, it will cost you more than machines value

Kyocera... | Answered on Jan 12, 2019


Kyocera Copystar... | Answered on Jan 11, 2019

The machine wants the cyan toner changed. There is a chip on the cartridge that the machine reads to reset the page count. Change the cartridge or find an aftermarket chip.

Kyocera Office... | Answered on Jan 10, 2019

this is most often seen when the default drawer is disabled...dashes instead of paper size. to reset drawer try touching 10871087 then 906 and the start button this resets the disabled drawer. also make sure no paper is stuck behind the drawers.

Kyocera Copystar... | Answered on Jan 10, 2019

Kyocera-Mita TASKalfa 1800 Error Code: 7900DescriptionDrum EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively.
CausesDR PWB. Main/Engine PWB. 1800&code=7900

Kyocera Office... | Answered on Jan 10, 2019

Not finding what you are looking for?
Kyocera Logo

Family Lines

4,533 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts


Level 3 Expert

83850 Answers


Level 3 Expert

904 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides