How do you preset radio stations for a lenoxx electronics CD-160? i went to its website and i got a virus :S

try to replace it with a different CD player

There are about six common cords that fit most items, Radio Shack is a good place to start and most TV repair shops carry power cords

Hello
There are 6 preset position available for each radio band.
For programming, Radio must be ON. Tune to a station. Press MEMO/DEMO. Press any button 1 to 6. The tuned station will be memorised on the number you select by button press. Repeat using a new station and preset number. There is no atu preset option available with this device. You have to store stations you want according to your preference. Only 6 station positions for each band [total 12 positions] together with AM and FM bands.
To recall the stored stations, press the desired number 1 to 6.

Hello
[1] Press RADIO BAND.AUTO PRESET until the band you want appears on the display [direct power ON]. Each time you press the button the indication changes as follows. "FM" => "AM"
[2] Hold down TUNE+ or --ve until the frequency digits begin to change in the display.
The player automatically scans the radio frequencies and stops when it finda a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step.
If FM band is noisy, press the MODE repeteadly until "MONO" appears in the display and the radio will play it monatural. If FM radio signal at your area is very weak, this type of noise may occur. OK.

Click below for the manual.

manual

1 Select the radio band and tune in a desired radio

station you wish to store in the preset memory.

2 Press (PRESET).

The Preset screen is displayed.

3 Rotate the Double Action encoder to select the

preset number.

4 Press and hold /ENTER for at least 2 seconds.

The selected station is stored.

The display shows the band, preset number and station

frequency memorized.

• A total of 18 stations can be stored in the preset memory (6 stations

for each band; FM1, FM2 and AM).

• If you store a station in a preset memory which already has a station,

the current station will be cleared and replaced with the new station.

• Press in the outer ring and rotate the Double Action encoder to the

left or right on the Preset screen, you can switch the Preset screen of

another band.

FM-1 FM-2 AM FM-1
You can also change the desired radio band by pressing BAND.


Hope this helps.

Zeppelinx12

You might find your unit here:

http://www.retrevo.com/samples/Lenoxx-manuals.html#Radio

http://www.retrevo.com/samples/Lenoxx-CD-Player-manuals.html

PRESET RADIO STATIONS
1 press RADIO BAND. AUTO PRESET to select the band.
2 Hold down RADIO BAND > AUTO PRESET for 2 seconds until "AUTO"flashes in the display
3 Press DSPL/ENT/MEM. The stations are stored in the memory from the lower frequencies to the higher ones.

if a station can not be preset automatically.
you need to preset a station manually.
1 press RADIO BAND. AUTO PRESET to select the band.
2 tune int he station you want.
3 hold down DSPL/ENT/MEM. for 2 seconds until the preset number flashes in the display.
4 press PRESET + or - until the preset number you watn for the station flashes in the display.
5 press DSPL/ENT/MEM. The new station replaces any old one.

TIP the preset radio stations remain in memory even when all power is disconnected.

manual available at sony
http://www.docs.sony.com/release/CFDF10.pdf

Blaupunkt CD32  Code Entry 

Turn on the radio, the display will show 'CODE' followed by '0000'

Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the fourth digit

Finally press the [ station ^ ] button to save.

Blaupunkt Boston CC-22 Code Entry 
Turn on the radio, the display will show 'COD'

Press preset [ 1 ] repeatedly for the first digit followed by [ station + ]
Press preset [ 2 ] repeatedly for the second digit followed by [ station + ]
Press preset [ 3 ] repeatedly for the third digit followed by [ station + ]
Press preset [ 4 ] repeatedly for the fourth digit followed by [ station + ]

Finally press the [ station + ] button to save. 

http://www.alpine-electronics.co.uk/index.php?id=915&L=&manualsearch=CDM-7859RB

User Guide can be downloaded from here


Mark