Power button bilinking

First things to try:

1. Unplug the fridge and move it away from the wall. 2. Inspect the power cord for damage. Replace the power cord if it is damaged. 3. Plug the fridge back into the wall outlet. 4. Set the temperature control to the desired level. 5. Push the "Reset" button, located near the temperature control panel, to reset the temp control settings. The Reset button is usually red in color. 6. Move the fridge back to its original position.

This sounds like a main power board usually capacitors but try a power cycle which is unplug tv and take cord off of tv. Hold power button in 25 seconds then plug it all back in however hook it up to a different wall outlet even with an extension cord if your tv is too big to move we just want to rule out the wall outlet in this testing. If it is something and you feel comfortable doing it you can get parts at shopjommy.com or check other places too.

Unplug the power cord from the wall outlet.

Unplug the power cord from the all-in-one.

Wait 30 seconds and plug the power cord back into the wall outlet.

Press the Cancel and Right Arrow buttons.

While still holding the buttons, plug the power cord back into the all-in-one. Continue to hold the buttons for two seconds, and then release them.
Use the On button to turn the power off and then back on again.

If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

TRY THIS

1. • 1 Turn the TV off with the front-mounted power button, not the remote. Unplug the TV's power cord from the wall outlet. Let an hour pass before plugging the cord back into the wall outlet. Turn the TV back on with the front-mounted power button and wait until it has fully restarted. Bring up a TV channel to see if the image being presented on the LCD screen is no longer flickering. A momentary power surge can cause the circuitry inside the LG-brand LCD TV to function erratically.
     
   • 2 Unplug the video cable from the video connection on the back or side panel of the LG TV. If more than one video cable is connected to the TV, disconnect all of them. Disconnect the other end of the video cable from the video source device that it's attached to -- a DVD or Blu-ray player, or a satellite receiver or cable box. Blow off the connections on the video source device and on the back or side panel of the TV with bursts of compressed air. Reinsert one end of the video cable into the video source device and the other end into the video input that it was connected to. Turn the TV back on with is remote to see if the picture is now free of flickering. A loose or partially connected video cable can cause the LCD TV's screen to flicker when presenting an image.
     
   • 3 Turn the TV off and unplug its power cord from the wall outlet. Place a power conditioner next to the wall outlet. Plug the power conditioner's power cord into the wall outlet. Plug the TV's power cord into one of the AC sockets on the power conditioner. Turn the power conditioner on. Turn the TV on to see if the picture is now free of flickering. The RF signals in the electric line that the LG TV is drawing power from can cause flicking through interference patterns being generated.
     

• unplug the power cord from the back of the printer and from the wall outlet
• hold down the power button for a minute to drain power
• plug the power cord back in to the wall
• press # and 3 on the keypad while plugging in the power cord to the back of the printer
• let go of the keys when the printer starts up

: Check the power cord

1.
Turn on the product.
2.
Remove the power cord from the back of the product.
3.
Check the power cord for any physical damage. If the power cord is damaged, replace the power cord.

*
If these steps resolved the issue , you do not need to continue troubleshooting.
*
If the issue persists , continue to the next solution.

Turn the product off and then on again

1.
Press the Power button ( ) to turn the product off.
2.
Wait 60 seconds, and then press the Power button ( ) to turn the product back on.
3.
If the product does not turn off when the Power button ( ) is pressed, wait three minutes, and then proceed to the next solution.

Plug the product into a wall outlet
Follow these steps to make sure the product is plugged in correctly.

1.
Unplug the power cord from the back of the product.
2.
Unplug the power cord from any surge protectors or power strips.
3.
Select a wall outlet to plug the product into. Test the wall outlet by plugging another electric appliance, such as a lamp, into the wall outlet and turning it on. Unplug the test appliance.
4.
Plug the power cord into the back of the product.
5.
Plug the power cord into the wall outlet.
6.
Press the Power button ( ) to turn the product on.

*
If these steps resolved the issue , you do not need to continue troubleshooting.
*
If the issue persists , continue to the next solution.

Solution six: Reset the product
Follow these steps to reset the printer.

1.
Unplug the power cord from the back of the product.
2.
Unplug the power cord from the wall outlet.
3.
Wait 10 seconds, and then plug the power cord back into the wall outlet.
4.
Plug the power cord into the back of the product.
NOTE: Many power cords have an LED light on the power module or on the end of the cord that plugs into the product. Make sure the LED light is lit and steady.
5.
Press the Power button ( ) to turn the product on.

*
If these steps resolved the issue , you do not need to continue troubleshooting.
*
If the issue persists , continue to the next solution.

6. Perform a partial reset of the product

1. Disconnect the power cord from the product.
2. Wait for 20 seconds.
3. Press and hold # and 3 while reconnecting the power cord.
4. When the product turns on, release both buttons.
5. Try printing again.

IF still won't resolve it by following steps mentioned above then your printer needs replacement. Malfunctioning hardware.

Try doing this procedure to correct the problem.

1. Unplug the power cord from the back of the product.
2. Unplug the power cord from any surge protectors or power strips.
3. Select a wall outlet to plug the product into. Test the wall outlet by plugging another electric appliance, such as a lamp, into the wall outlet and turning it on. Unplug the test appliance.
4. Plug the power cord into the back of the product.
5. Plug the power cord into the wall outlet.
6. Press the Power button to turn the product on.
7.Now check if its already working.

perform power cycle
1. Unplug the unit’s power cord from the back of the printer while the printer is 'on'.
2. Hold down the ‘On’ button for 60 seconds
3. Plug the power cord back to the unit while holding the ‘On‘ button down.
4. This will reset the printer’s mechanical systems and discharge all capacitors.
If the issue still persists, then

1. Unplug the power cord from the wall outlet.
2. Unplug the power cord from the all-in-one.
3. Wait 30 seconds, and plug the power cord back into the wall outlet.
4. Press and hold the # and 6 buttons on the numeric keypad.
5. While still holding the buttons, plug the power cord back in to the all-in-one. Continue to hold the buttons for two seconds, and then release them.

This should resolve your issue.

The print carriage is stuck.

Solution

1. Open the top access door on the printer.
2. Remove the print cartridges.
3. Close the print cartridge flaps after removing the print cartridges.
4. Turn the printer off and then on again.
5. Replace the print cartridges.
6. Close the top access door.

If the resume light continues to blink after the print cartridges are released,

OR

the print carriage is stuck or makes a grinding noise, follow these steps.

Solution

1. Lift the top cover to the printer.
2. Turn the printer off and then on again.
3. Unplug the power cord from the back of the printer when the grinding noise starts. Unplug the power cord from the wall outlet.
4. Move the print carriage towards the middle of the printer (this procedure may take a couple of tries to get the timing correct).
5. Take out the print cartridges and close the top cover.
6. Plug the power cord into the wall outlet. Plug the power cord into the back of the printer.
7. Open the top cover, reinstall the print cartridges, and then close the top cover

Solution

1. Open the top cover.
2. Unplug the power cord from the back of the printer. Unplug the power cord from the wall outlet. Wait a minute or so.
3. Plug the power cord into the back of the printer. Plug the power cord into the wall outlet

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

First: Check the power outlet. Check it with a good lamp so you know you are getting power to the set.
Secondly: Check the power cord. Wiggle it around the molded ends to make sure it is not open inside the molded portion of the plugs.

Thirdly: If you know for sure the set is getting power and still no indication at all (you should be getting some little light on the front panel; standby indication) then there may be a fuse on the back panel or just inside the back cover (you will have to remove it; after unplugging the power cord) that needs replaced.

Fourthly: After all these checks if you are getting nothing, you may have some failure inside that is very serious. Normally we do not recommend serious repairs to a set over 4 years of age. This is because the set is likely to develop some other problem soon after the repair is made; further, the repairs are getting more expensive day by day while the price of new sets is coming down dramatically. Lastly, the new sets have better picture, longer lasting circuits and better features.

Hope this is a good solution for you.

thanks for your questions.