Question about Uniden Lands Phones

Open Question

I have a Uniden DECT 1735+3. One of the handset will register with the base. Hoe can I make the handset register?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: How to clear all registrations from the base

One has to completely deregister all handset by pressing end and # keys together till complete de registration is shown on handset screen. if the de registration is not done as above stated method the hand set will not register will show connecting on hand set screen.

Posted on Nov 07, 2008

Ad
  • 1 Answer

SOURCE: Register additional handsets on a Uniden phone

From: Uniden Customer Support

On most models you can find an option in the menu for De-register? In that case you would select that option and select to deregister the handset.
TRU88 models you go to the main menu and go to De-register HS select yes to deregister the Handset.

DCT5 and DCT6 models: Press menu on the handset. Go to System Reset and Press select. Go to Deregister HS and press select. Arrow up to yes and press select. Then go back into the menu. Go to system reset and press select. Arrow down to Replacing the base and press select. Arrow up to yes and press select.

DCT7 models: Press and hold "end" and "#" until the system reset menu appears on the display. Then follow the instructions from above for the DCT5 and DCT6 deregister procedures once your into the menu.

TRU4 and TRU5 models: Press and hold xfer/del and end until "de-register?" appears. Use the plus+ button to go up to yes and press select.

To register any of the following phones please see you owners manual under either:


•Register handset or


•Register the digital security code.

Posted on Mar 05, 2009

  • 3 Answers

SOURCE: cant register/install a new dect 6.0 uniden 2060 phone

I had a similar problem which I finally fixed. You did not say if any of your phones registered.
First try the following recommended by Uniden Support:
Your phone(s) should be fully charged before putting them on the main base.
Unplug the battery from the phone by removing the battery cover and removing the connector. Then, push the # and * key together and hold while you plug the battery back in (requires some dexterity). Continue to hold the two keys until you hear a confirmation tone. This will force the phone to reregister. Put the phone on the main base (if you are sure it has a fully charged battery) and see if it will reregister it to solve the problem.
That did not work for me. So, I followed the instructions to de-register the handset (even though it hadn't really registered). But, I also pretended like the Base was not available (because using the base in this step also failed).
1) Press and hold the hang up and # keys for at least 5 seconds.
2) Move the cursor to select Base Unavailable and then press Select.
3) Select the base you want to deregister from, press Select and then move the cursor to Yes and select.
This causes the phone to delete any of its base information.
At this point, again insure that your phone shows the battery is fully charged and if it is not, put it on the stand alone charger base (not the main base). With the battery fully charged, place it on the base and try registering again by placing it in the main base.
If neither of these approaches help, contact support at Uniden.com.
However, my problems were cleared when I cleared the handset with the second set of instructions.

Posted on Apr 26, 2009

  • 1 Answer

SOURCE: How to remove Uniden handset from base

The brillian people at Uniden don't feel it necessary to provide this type information in their manuals. You have to trial and error to find it, but what can you do. All you have to do to reset the base unit itself is to unplug the power, then while holding down the delete key, plug it back in. Hold the delete button down until you hear a beep, which indicates it has reset. Now you can readd handsets and they will start at 1.

Posted on Jun 27, 2009

  • 1 Answer

SOURCE: Reset base unit of Uniden TRU9485

Uniden TRU9485 (This didn’t work for me but this was the first instruction from Uniden Tech Support)

TO RESET THE BASE UNIT:
Unplug the base unit AC adapter.
Hold down for 15 seconds the DND, * and “menu” soft key (the middle silver soft key under the LCD) while plugging the base unit AC adapter back in.
All the settings should be reset.

Uniden TRU9485 (Worked for me)
ALTERNATE WAY TO RESET THE BASE UNIT:

Unplug the base unit AC adapter.
Hold down for 15 seconds the DELETE KEY (zero with a line through it) while plugging base unit AC adapter back in.
All the settings should be reset.

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do we program answering machine on dect 1735 cordless phone


Do you mean the Uniden DECT 1735? You can turn on the answering system from the base On/Off button. The rest takes the hanset or a call into the phone. Start with the phone in standby (no handsets in use). Press Menu on a handset. Use the Up/Down arrows to navigate to Answering Setup and press Menu again. To set the number of rings, navigate to Ring Time and press Menu again. Use the arrows to select a number of rings and press Menu to save. Press the Left arrow/Page key to go up to the Answering Setup menu. Press End to exit the menu system.

To set the greeting, you would navigate to Record Greeting in the Answering Setup menu. Press Menu. When you hear "Record Greeting", speak your message. Press Menu when you finish. Press End to save the message after you hear it repeated. Press Menu and wait for the "Record Greeting" prompt if you need to change the greeting.

The manual for this is available on the product site: https://www.uniden.com.au/product/dect-1735-2/. The direct link to the manual is currently https://www.uniden.com.au/wp-content/uploads/2017/06/DECT_17352_OM.pdf . See the section starting on page 20 for the different steps to set up the answering system.

I hope this helps.

Cindy Wells

Apr 15, 2018 | Dect Lands Phones

1 Answer

Sync


If by "sync a handset" you mean register a handset so it works with the base, then yes. It doesn't even need to be the same model. The manual gives instructions for registering a handset to work with the base. If you need a manual, select the model of your Uniden DECT 6.0 phone from the list beginning at http://www.uniden.com/owners-manuals/dect-phones/scat/dectphones_mnl .

Jun 03, 2013 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Reconnect handset to base


Since you didn't specify the model of your Uniden DECT 6.0 phone I can only suggest you select it from the list beginning here to download the manual. Follow the instructions to register the handset to the base.

Mar 01, 2013 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

Uniden phone stuck at searching, not getting a dial tone


One thing to try is deregestering your phone and registering it with the base again.

Hole the # and 'End' key on the handset until the next menu appears (about 5 seconds). Select deregister phone (use the 'Menu' button). Do it again, but select "base unavailable". After that, set them in the base (not the handset charger) and they should register with the base.

This works on most Uniden model phones.

Jan 29, 2013 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Handset won't connect to base unit


Try placing the handset in the base unit to register it. Then see if it is found by the base.

Mar 21, 2010 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

My cordless phone says "to register see owners manual for help" How do I get the phone working, it is a uniden DECT 6.0 Model DECT 1588-2


With the phone in standby, press MENU/SELECT on the base.
Move the cursor to select the Register Handset menu, and then press MENU/SELECT. Handset Registering will appear.
On the handset, press and hold # until the handset beeps and displays Handset Registering.
When the handset has registered to the base, the LCD will display Registration Complete then show the handset ID number.
If the display shows Registration failed, repeat the process again.
Note: If a handset has ever been registered to a base, reset the handset before you register it to a new base

Dec 21, 2009 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

I have a Uniden DECT 6.0 phone set. I damaged one


On the base, open the menu and select Register Handset. The display should say Handset Registering.
On the handset you want to register, press and hold # until the handset display says Handset Registering (about 2 seconds).
1.
2.
DSL filterTelephone cordTelephone wall jack
45
In about 30 seconds, the handset display should say Registration Complete. Press Talk/fl ash and make sure you get a dial tone.
If...
Try...
you don't hear a dial tone
the display says Registration Failed --
Making sure the handset is fully charged, then start over at step 1.

Sep 07, 2009 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Redistration to other brand DECT 6.0 base failed.


DECT 6.0 IS JUST A MARKET NAME FOR DIFFERENT BRANDS, THE WATERPROOF DWX207 WILL ONLY WORK WITH UNIDEN PHONES, ONLY BECAUSE YOU WANT THEM TO WORK TOGETHER DOES NOT MEAN THEY WILL WORK TOGETHER...

May 22, 2009 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Uniden DECT 6.0 - 2 Handset


You may have to manually "register" your handsets to the base. This is supposed to do it automatically but there are instructions for "registering" your handsets if the automatic feature fails or you add a new base, etc. Consult your owner manual for instructions.

Nov 29, 2008 | Uniden DECT 6.0 Cordless Telephone...

3 Answers

Uniden dect6.0 handsets do not operate


I am writing for my Mum, who is 99. We live far apart, so it is a bit difficult to fix her problem. She had a new Uniden DECT 60 (?) installed in early July. It seemed to be working fine when we left her, but she says it only rings twice before going to voice mail. She says it has always been like that. How can we fix this for her even though we live at a distance?.

Mar 12, 2008 | Uniden DECT 6.0 Cordless Telephone...

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

k24674

Level 3 Expert

8081 Answers

Cindy Wells

Level 3 Expert

5866 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...