Uniden Lands Phones - Recent Questions, Troubleshooting & Support

I find no way to disable the CID record feature.

If you wish to neither see nor record CID, contact your service provide and unsubscribe to the CID service.

A copy of the user manual is available at;
http://www.uniden.info/download/ompdf/DECT1580om.pdf

To delete all the recorded Caller ID numbers with the handset do the following;

When the phone is in standby, press ID (on the 4-way navigation function key), then press MENU/SELECT, then select Delete All. When the phone asks you to confirm, select Yes.

http://www.fixya.com/support/t1576275-uniden_phone_says_line_hold_50_time http://www.fixya.com/support/t1576275-uniden_phone_says_line_hold_50_time

Likely the two ring answer is "toll saver" You'll need to retrieve new messages. Once all new messages have been reviewed, it should return to the programmed number of rings, see "ring time" in the manual.

ALL messages may be deleted as follows;
delete all messages With the phone in standby, press Delete; press Delete again to confirm.


If answering system messages have been retrieved, a continuing flashing indicator could be your voice mail service;

Voice Message Notification • If you subscribe to a voice mail service, your phone can notify you when you have a new message. This feature supports Frequency-Shift Keying (FSK) notification. Contact your voice mail provider for information. • When you have new messages, the display shows a message icon. After you listen to your messages, the message icon turns off. If it doesn't, you can reset it. With the phone in standby, open the menu and select Global Setup; select VMWI Reset, then select Yes
A copy of the manual is available from Uniden;

A copy of your manual can be downloaded free of charge from;
http://www.uniden.info/download/ompdf/D1788om.pdf

Suggest you reset handset and register again with base.

Instructions from manual...
Resetting Handsets If you have trouble with a handset or if you want to replace one, clear the registration information from the base and the handset: 1. Press & hold END and # at the same time until you see the System Reset menu. 2.If you still have the base the handset is registered to, select Deregister HS, then select the handset you want to reset. If you don't have that base anymore, select Base Unavailable. 3. To confirm, select Yes. The handset displays Handset not registered. Registering Handsets If you see a "not registered" message on a handset, you must register it to a base before using it. 1. Place the handset in the base; the display should say Handset Registering. 2.Wait until the display says Registration Complete (about 30 seconds), then pick up the handset and press TALK/FLASH. 3.If you don't hear a dial tone or the display says Registration Failed, charge the battery completely, then try again.

Our just started to do the same thing. Drove us crazy because there were no messages. I couldn't find the manual so I looked up the manual on their website. Here's how to fix it....IT WORKS! With the phone in "stand by", open the menu and select Global Setup.Select VMWI reset. Then select yes.

The handset may be out of range in relation to the base.

Likely unit kaput, but battery suspect.

Try different battery, not necessarily new but if you have a second known good Uniden handset with same battery, swap batteries.

Likely its a pending VoiceMail not answering machine.

See...
http://www.fixya.com/support/t3030275-red_message_light_blinking_uniden_phone

I have a Uniden 5.8 GHz and the message indicator light will not stop flashing. The phone screen says I have a voice mail but I don't. Does anyone know to fix it?

I had the same problem. Something makes the phone's memory get "stuck."  Take the battery out of the phone for a minute and then put it back. Then unplug the phone and plug in again. You need to do this with all extensions. The problem goes away. 

I suspect remote is unable to communicate with the base and is reporting the issue as power loss at base.

So does the base function, makes and receives calls?

Reset the base unit and power supply by unplugging the base power supply from the wall, wait at least 1 minute, plug base power supply back into wall outlet.

Reset remote by removing battery wait a minute, reinstall battery.

If after the reset the base can't make/receive calls, its likely failed.

If the base works and the remote still reports base power issue, could be either base or remote.

The manual is at the following link...

http://www.uniden.info/download/index.cfm?s=D3098

What is phone system connected to ?
A land line ?
what sort of diversion ?
unconditional *21{phone number}# #21# to turn off unconditional
no reply / busy ? https://infinititelecommunications.com.au/network-feature-codes/
https://www.telstra.com.au/small-business/online-support/category/bundles/dot/where-can-i-find-a-list-of-feature-access-codes

My Uniden manual refers to pressing a [dnd] (do not disturb) key on the base.

• You are urged to arrange for periodic performance checks with a
Uniden Marine dealer

This info is from page 34 of the operation manual which is available on the internet in pdf format:
•To edit the number, press END/CLEAR. to back up the cursor and delete numbers. Re-enter the correct numbers.