Why is broiler not igniting? - Electrolux Kitchen Ranges

There are a few potential issues that could cause the problems you're experiencing with your Jenn-Air broiler. Here are a few things you can try:

1. Make sure the gas supply to the broiler is turned on and that there are no blockages in the gas line.
2. Check the gas valve to make sure it is open and functioning properly.
3. Make sure the gas burners are clean and free of any debris or obstruction.
4. Check the broiler burner for proper ignition. It should ignite within a few seconds of turning on the broiler. If it does not, the burner orifice may be clogged and will need to be cleaned.
5. Check the gas pressure to the broiler. If the gas pressure is too low, it can cause the flames to be low or go out.
6. Make sure the broiler igniter is properly seated and connected.

Ours did that and I had to replace the igniters that did not work.

Electrolux Oven Broiler Not Working - Model E30DF74EPS ...

www.repairclinic.com/...Range-Stove-Oven/...-/Electrolux-Oven-broiler-...

Most Frequent Causes for Oven broiler not working. See All Range/Stove/Oven Parts for model E30DF74EPS. Cause 1 Temperature Control Thermostat.

Electrolux Oven Broiler Not Working - Model EW27EW65GS6

www.repairclinic.com/...Range-Stove-Oven/...-/Electrolux-Oven-broiler-...

Electrolux oven broiler not working? Use our DIY troubleshooting & videos. Then, get the parts you need fast. Return any part for 365 days.

Oven Broiler Not Working - Repair Parts - RepairClinic.com

www.repairclinic.com/...Range-Stove-Oven/...---/Oven-broiler-not-worki...

Oven broiler not working? Use our DIY troubleshooting & videos. Then, get the partsyou need fast. Return any part for 365 days.

Gas Oven/Broiler not working/igniting - ApplianceBlog

In my case, the igniting wire was too close to another piece of metal. It was igniting upstream from the burner. All I did was push up on the wire, and the broiler started working again!

Based on your description, the igniter is dead.
The broiler and the oven heat each have their own igniter. Look for the characteristic glow when the oven is turned on. If it is not visible, then you will need to replace the "OVEN" igniter...
Google the stove model for repair parts and locate the igniter. Not too hard to replace... directions are packed with the new igniter...

Each burner manifold in the oven has its own igniter. If the igniter is defective, the burner assembly will not light. The igniter has to be functioning properly in order for the gas safety valve to open. This is a designed safety feature that prevents free flowing gas from entering the oven cavity without ignition. This reduces the risk of explosions.

There should be a flame spreader metal plate covering the access over the broiler. You will need to access the broiler so you can view the broiler manifold and igniter. Turn the oven setting to broil and make sure the igniter begins to glow. If the igniter fails to glow, replace it. If the igniter does glow, but you still do not have ignition after 90 seconds, the igniter may be weak and still require replacement. The following link explains oven igniter types, their current potential, and how to replace them:

http://www.fixya.com/support/r401858-replacing_oven_igniter_gas_range

If you have questions, or require additional assistance, please let me know before you rate the solution. I hope this helps you.

Oven bake ignites usually have lifetime 5-7 years. If igniter glows but gas not came in - replace igniter. Same with broil igniter.

I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

hi yes you could replace the broil for the bake but they are very fraglle so i would buy a new bake igniter replace

does the board control both ignitors and if so your right the ignition board is bad.

you may not need a igniter. the problem could be with your control board which supplies power to both the broil igniter and the oven igniter. In my years of working on ovens i have not seen a oven that needed both igniters replaced.