How to get channel setup highlighter so I can choose it and set TV in antenna mode?

What is the TV source or input? Unless the source is antenna or cable using the antenna in, the captions have to be disabled at the set-top box that is providing the signal. Some set-top boxes have a CC button on the remote but many have this hidden in the menu system.

My IPTV box requires me to press Menu, choose the Settings menu and then enter a code provided by the provider. Once in the menu, the captions are enabled in the Hardware > Audio menu. Some satellite dish set top boxes have different access methods depending on the TV setup. If you have a master box that feeds two TVs, the setting menu to control the closed captions was only available on the TV closest to that box. (This was the case for a Dish receiver with a Single or Dual mode. In single mode, turning on the CC enabled the captions for both TVs. In dual mode, the two TVs could be tuned to different channels but only the TV nearest the set top box would display the closed captions if the feature was enabled. On that receiver, the closed captions were reached by pressing Menu. Then the captions options were under Properties > Closed Captions.)

Please indicate what the TV source is for further information on where the sub-menu for the closed captions will be toggled on and off.

I hope this helps.

Cindy Wells

Go to source and highlight tv air then channel search

You should be able to get OTA (over the air broadcast) just make sure you have an antenna plugged in and that the tuner is set to AIR.

Setting the Tuner Mode
If you are using a device that is connected to the RF input, such
as an external antenna or cable TV connection, you must set the
tuner mode.
1. Press the MENU button on the remote. The on-screen menu is
displayed.
2. Use the Arrow buttons on the remote to highlight the
Settings icon and press OK. The Settings menu is displayed.
3. Highlight Tuner and press OK. The Tuner Mode menu is
displayed.
4. Highlight Antenna or Cable and press OK.
5. Press the EXIT button on the remote.
Scanning for Channels
Before the TV can detect and display channels and their
associated information, you must scan for channels. A channel
scan may also be necessary when the TV has been moved to an
area where different free-to-air broadcast television channels are
available.
1. From the Tuner Settings menu,
highlight Auto Channel Scan.
The auto channel scan begins.
2. Wait until the channel scan is
100% complete. Highlight Done
and press OK.
3. Press the EXIT button on the
remote.

Hello, with the set on, press the menu button, move the cursor down till the "Tuner" section is hi-lighted, click on it. Then the first selection is "Tuner Mode" click on it, the choose "Antenna" click on it. Then move to the "Auto Channel Scan" and click on it, and let it set all your channels. when done, just exit menu and change channels as desired. you can go to page 39 in your manual for these instructions: Tuner Mode
Select Cable or Antenna depending
upon which equipment you have
attached to the DTV / TV Input.
Auto Channel Search
Automatically search for TV channels
that are available in your area. Be
sure to first select the correct tuner
mode above. The TV will search for
analog and digital channels. When the
search is done, press EXIT to begin
watching your programs. thanks, Terry

Hello
You can autotune your Sony TV without a remote control. Fist connect it to an external antenna or cable whatever may be, to its antenna socket at the back side.

After you have finished connecting your TV, you can use Auto Program to set up your

channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.

[1] Press POWER button on the TV to turn it on. The Initial Setup screen appears.

[2] Press CH+ button on the remote control or on the TV front panel to start Auto Program, or press CH-- button to exit.

The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.

To perform Auto Program again

1 Press"MENU" button on the front panel of your TV.
2 Press "RIGHT ARROW button to highlight Channel Menu.
2 Press DOWN ARROW BUTTON to highlight CABLE or ANTENNA AND PRESS [+} to select.

4 Press UP arrow or DOWN arrow to highlight On or Off according to how you connected your TV. Press [+] to select.

4 Press F or f to highlight On or Off according to how you connected your TV. Press to
select
5 Press DOWN arrow button to highlight Auto Program. Press [+]to search for channels
6 After Auto Program finishes, press MENU button to exit.
OK

Hello
Your Toshiba tv can be automatically tuned to all stations. The procedure follows.

Programming channels automatically

Your TV can automatically detect all active channels and store them in

its memory. After the TV has stored the channels in its memory automatically,

you can add or erase channels manually.

To add channels automatically:

1. Press MENU, then press "left arrow" or "right arrow" button to display the SETUP menu.

2. Press "Up arrow"or "down arrow" until the TV/CABLE

selection is highlighted.

3. Press "left arrow" or "right arrow" button to highlight either

TV or CABLE, depending on which you use.

If you use an antenna, choose TV.

If you use cable, choose CABLE.

4. Press "down arrow" button until the CH PROGRAM selection is highlighted.

5. Press "left arrow" or "right arrow" button to start channel programming. The TV will automatically

cycle through all the TV or Cable channels (depending on which you

selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message

"PROGRAMMING NOW-PLEASE WAIT" appears.

6. When channel programming is complete, the message "COMPLETED"

appears.
7. Press CH UP or DOWN button to view the programmed channels.
OK.

It is important for the TV to know what type of
signal-Cable TV (CATV) or a normal antenna
you are using. Choose your signal (Antenna or
Cable):
Press MENU to see the main menu.
Press CH+ or CH- to highlight Setup.
Press OK to enter the Setup submenu.
TV/CATV is highlighted. Press VOL+ or
VOL- to select TV or CATV.
Choose CATV if you have Cable TV
service. (See page 4 for connection
details.) If you do not have Cable TV
service and you connected an antenna
to the TV, choose TV. (See page 5 for
connection details.)
Press MENU repeatedly to exit the
menu or the menu will automatically
disappear within a few seconds if no
buttons are pressed on the remote
control.

And here is the manual if you need .

http://tv.rca.com/RCATV/Assets/pdfs/27F520T_1641312E_IB_e-06.pdf

Good luck and please rate

Setting Up the TV
After you have finished connecting your TV, you can use Auto Program to set up your
channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.
(Make sure CABLE is connected on coaxial and you are not using any other connections such as cable box, hdtv or satellite antenna)

1 Press to turn on the TV. The Initial Setup screen appears.
2 Press on the remote control or on the TV front panel to start Auto Program, or press
to exit.
To perform Auto Program again
1 Press .
2 Press g to highlight Channel Menu.
3 Press f to highlight Cable. Press to select.
4 Press F or f to highlight On or Off according to how you connected your TV. Press to
select.
5 Press f to highlight Auto Program. Press to search for channels.
6 After Auto Program finishes, press to exit.
To reset the TV to factory settings
1 Turn the TV on.
2 Hold down on the remote control.
3 Press and release the POWER button on the TV front panel. The TV will turn itself off,
then back on.
4 Release .
✍ When you start Auto Program wait until it is finished; otherwise it will skip over channels that are
available. Perform Auto Program again to program receivable channels.
✍ The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.
Initial Setup
Auto Program [CH+]
[CH–]
First please connect
cable/antenna
Exit

Hi albertogiler, I am happy to help, you will need to attach a antenna to the tv to pick up OTA over the air signals, depending on your location you may be able to use a set of rabbit ears, I have provided a link to a site that will explain in depth. http://www.antennaweb.org/aw/welcome.aspx
Let me know if this helps and please rate this solution. lone99star

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee

Most TVs have a choice of air or cable in the menu portion of the tv. press menu go to setup and from there you should see an option that says air/antenna or cable. You will have to either toggle to get the air selection or highlight it. Then you should be able to get to channels you need.

An easier solution may be to go to the Dish receiver that controls the image on the tv you can't get to 73. With tv and satellite on (make sure both green and blue lights are on) press on your Dish remote #1 with the green tab on the bottom the following sequence: MENU - 6-1-5. tHIS WILL TAKE YOU TO THE MODULATOR SET UP PAGE. Move the highlight from cancel to the mode section an highlight AIR and press select. Then move the highlight back to the right to DONE and press select. Press cancel three times or view live tv. then go to the other tv and put it on ch 60.
Hope this assists you.