Question about Home

1 Answer

Braun thermoscan 6022

I am constantly getting a LO reading. No temp being displayed. Batteries have been changed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,509 Answers

It's probable that it needs a new lens filter or the filter needs cleaning. I have no idea how to remove the filter but it probably clips or screws off the bit that goes in the ear.
Quite frankly the device is at best unreliable, it measures infra-red in the ear, great in theory but not very reliable in practice. I would use a different thermometer.

Posted on May 15, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: I have a braun thermoscan 6022 after it displayed

Ambient temperature is not within the allowed operating range (10 - 40 °C or 50 - 104 °F).
Allow the thermometer to remain for 30 minutes in a room where the temperature is
between 10 and 40 °C or 50 and 104 °F.

Here is a link to the manual if you should need it:

http://braun.kaz.com/files/IRT33020COGB,%20F,%20E,%20P.pdf

Posted on Mar 17, 2011

  • 8 Answers

SOURCE: We have the Braun 6022

If you whish to switch from Celsius to Fahrenheit, proceed as follows:

(1) Make sure the thermometer is turned off.

(2) Press and hold down the Start button (IRT 4020)
or the «I/O» button (IRT 4520). After about
3 seconds the display will show this sequence:
«°F» / «SET» / «°C» / «SET» ...

(3) Release the Start button / «I/O» button when the
desired temperature scale is shown. There will be
a short beep to confirm the new setting, then the
thermometer is turned off automatically.

Posted on Mar 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The indoor temp on my acurite model 02086 weather stn. constantely reads 26c how do I get it to read the correct indoor temp?


The manual of unit will tell you how to change reading from Centigrade to Fahrenheit. Read it carefully for details.

Oct 02, 2016 | Measuring Tools & Sensors

1 Answer

Oven thermometer only displays lo


I just had that LO reading. Pulled back on the tip of the thermometer. Seems I had it inserted into my turkey too far. Probably up against a bone or too close to the center. Good luck! Happy Thanksgiving 2016!

Dec 25, 2013 | Farberware New Classic Alert Oven Probe...

1 Answer

Envirastation model dws 170


Usually it is due to bad batteries or remote is too far away from home unit. Put units next to each other and press the channel button on front of the home unit. It will start a search to find the remote. If it finds it with a temp reading press the channel button again and you should hear a beep. Channel is locked in. If you still do not get a temp reading try changing batteries in both units and try again. Another try is to unplug the home unit and wait several minutes with no batteries in either house unit or remote. Replace batteries in remote then in house unit and plug back into power. Set all settings and see if you get the reading. If not try step one again. Weak batteries will do the same thing as well as remote to far away from unit.

Oct 06, 2013 | Measuring Tools & Sensors

1 Answer

The digital thermometer was flashing "lo". I assumed it needed new batteries and then replaced them. It is still flashing lo, but also showing a C reading. What do I need to do to reset it?


there should be a setting on it that changes the temp from Celsius or "c" to ferinheight and lo means that it currently isn't reading a temperature in the normal range. try running it under hot water and see if it says error or high.

Jul 15, 2011 | Prestige Medical Infrared Ear Thermometer

1 Answer

Batt Lo Displayed. I replaced with new batteries. The display still reads Batt Lo and I cannot changed temperature, etc.


sometimes you can bend out the battery holders to allow more tention on the batteries but thats only a temporary repair. a new thermostat is needed

Oct 28, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

No display on Robertshaw 9600; unit seems dead/furnace works


Hello
you have to have a thermostat! The thermostat tell the unite what to do. Get a new one.

Jul 25, 2009 | Honeywell Programmable Thermostat Heater

1 Answer

Reset Heating/ AIr cond temp display as well as EXT temp ????


the temp display can be switched between celsius and farenheit readings, since the car is from europe the default is celsius, The manual has instructions on changing back, You have to hold 2 buttons on the display per the manual.

May 07, 2009 | 2003 Land Rover Discovery

Not finding what you are looking for?
Home Logo

Related Topics:

607 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Experts

US Parts Center
US Parts Center

Level 3 Expert

719 Answers

Donni Steen

Level 3 Expert

687 Answers

john h

Level 3 Expert

21945 Answers

Are you a Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...