Circuit breaker Hi have A precor 932i have no power outlet has power checked circuit breaker with ohm meter keep getting a - number cord looks good

20 Most Recent Precor 956I Experience Treadmill Questions ...
Apr 12, 2012
20 Most Recent Precor 9.33 Treadmill Questions & Answers
Apr 12, 2012
20 Most Recent Precor 932i Treadmill Questions & Answers
Apr 11, 2012
20 Most Recent Precor C966i Treadmill C 966i Questions & Answers
Apr 25, 2010
More results from www.fixya.com

Hi Wimbledon.
see if this youtube helps you out.
Treadmill How to Check and Replace Control Board Fuse
or this link.
Precor 932i treadmill where is the fuse Google Search

I have the same saw.

Sorry but this question has to be asked, is the AC (Alternating Current) outlet working/ an live outlet? Had to ask.

If outlet is good move on to the next steps.

Take an ohm meter / continuity meter.

With the AC power cord unplugged from the AC wall outlet.

Place the two test leads from the meter onto the plug prongs .

With the switched closed/ON, you should get zero ohms (or very low, close to zero/ continuity).

In your case you probably will not have any continuity because it doesn't turn on.

Now comes the fun part trying to find the problem/ open connection.

Lots of possibilities.

1. The AC cord could be bad at the plug end.
   

2. The AC cord could be bad at the point entering the table saw.
   

3. The motor could be bad.
   

4. The brushes in the motor could be bad.
   

5. The field winding in the motor could be open/bad.
   

The plan is to ohm/continuity check the path of the power going to the motor, (both sides of wiring).

While meter leads are on the AC plug end, wiggle the strain relief ends. You have an intermittent connection.

TROUBLE: SAW WILL NOT START

PROBLEM 1. Power cord is not plugged in.

2. Fuse or circuit breaker tripped.

3. Cord damaged.

4. Burned out switch.

REMEDY 1. Plug saw in.

2. Replace fuse or reset tripped circuit breaker.

3. Have cord replaced by an Authorized Skil Service Center or Service Station.

4. Have switch replaced by an Authorized Skil Service Center or Service Station.

HI There,

Did you get this worked out? Possibly the IFT drive?

Typically on the Precor Treadmills if there are errors on the unit, you can press and hold the stop button for 3-5 seconds and it will go into the error log. Not sure what model you have.
E-2 is not what normally shows up on the screen. Do you mean Error 2 was displayed? From what I have read on Error 2's it could be a upper PCA issue, or possibly a dip in AC input during the power up sequence.
Treadmills require a dedicated line, meaning it is on its own dedicated circuit on your fuse panel/circuit breaker.
What exactly is the treadmill doing? Is it constantly showing Error 2 on the screen? Call up Precor tech support. They will be able to give you advice, and or get you connected with an authorized Precor factory trained technician who will be able to get you back up and running.

http://r.ebay.com/zK31KK check out this link..might be a interested to u..if interested call 3477376296

Dear Sir:I am recommend you to exchange the board. If you do not have ENOUGH experience will be better to buy a new one, or call some tech profesional for to execute this delicate work.
The causes can be various, Maybe you have SHORT circuit in the motors, power supply, see the block diagram.
God bless you

Hello Dale,

Having checked the thermal fuseto be good i will give you a partial list other things that could make the dryer not start

start switch

door switch

timer

circuit breaker, use your meter set to volts ac and check for 240 vac at the outlet,if 240 not at power outlet check for burnt connection inside outlet or bad circuit breaker

if 240vac at outlet check for 240 vac at terminal block on back of dryer where cord connects,if 240 at outlet but not terminal block replace cord , if burnt connection at terminal block,replace cord and block

finally the motor,manufactures do not publish wiring diagrams online and the only way for me to tell you to use jumper cord to check motor is find the wiring diagram inside of control panel and place one wire on the terminal indicated as neutral on wiring diagram and one wire on terminal indicated on diagram as run winding

firstly though check door switch to have contunity (0 ohms) and the start switch to have (0 ohms)WHILE PUSHING IT IN(the start switch isa momentary contact switch and will only have contunity while its pushed in)
to check timer again use wiring diagram and find chart that shows various cycles and with timer set to a cycle the two wires is says will have contunity will be indicated by a solid black line on the diagram

Good luck, Gene

Hi,
No it needs to have power to work....you plug the one unit into a powered outlet and then you can "find" the breaher in the panel with that unit...
For what you want to do you need an "Ohm meter" which integrated into many electrical meters.

heatman101

heatman101

The circuit breaker trips because you have some sort of short circuit. Use a Meter set to OHMS, and try to find the "Short". Check the wiring in the Plug also.