Apply patch into k770i - Sony Ericsson K770i Purple 3G Camera mobile+256mb Cellular Phone

i use cheap contact cement (dollar store tube works fine) and a bike tire inner tube (much better than crummy patch the give you) and apply some glue around hole and on bottom of patch, apply it smoothly, and aplly glue around edges (seams ) of patch. let dry for 2 days, if your using the transparent patch its like a sticker peel and smooth it on and let it dry for 2 days( in my opinion and experience they ****)

Hi rh57...

I will recommend that you use some contact cement, and a piece of thin plastic like a plastic drop cloth, shower curtain, etc.
Cut the plastic piece that will be using as your patch about 1" X 1" square.
Locate the hole in the air mattress, deflate air mattress, apply contact cement lightly to the air mattress approximatly 1" X 1" and the piece of thin plastic material you will be using as the patch over both entire surfaces of the patch and mattress...let it all dry about 20 mins.
After it is dry then apply the patch to the hole in the mattress, apply a weight to the top of the patch, let sit about half an hour and you are done
Hole fixed
Please take time to rate me thumbs up

If the holes are small, a dab of rubber cement on the holes may be sufficient to seal them. Larger holes will require a patch of the same or similar material as the mattress itself.

To properly adhere a patch, roughen up the mating surfaces of the mattress and the patch. Sandpaper is ideal. Be sure the mating surfaces are clean and free of dust. Apply rubber cement to the patch and apply it over the hold. Apply pressure to the patch using weights (a stack of books work great). Let the repair sit this way for the duration of the time required for the cement to set up according to the instructions on the cement.

Hope this helps.

Regards,

DIYpro

If this is on top or below (soffitt) If the cracks are movement or shrinkage when poured you can cut with Diamond grinder in a V type and then patch with a epoxy and sand fillers.If they are bigger you can use a repair motar .Your local hardware should have these in basic form.

I have seen this under XP SP3. The following solved the problem for me.

Install Corel 8 from the CD. Reboot.

Get the 369 and 433 upgrades from the Corel FTP site. (Those upgrades are no longer available on the web site, but there is a pointer to the FTP site on the "Updates and Patches" page).

Apply the 369 patches. Doesnt matter what version the CD is -- the patches check to see if they need to be applied. Reboot.

Apply the 433 patches. Reboot.

Start the XP Compatibility tool. Make the settings for PhotoPaint and Draw "Windows 2000", "No XP Themes." Reboot

my mobile k770i net work problem

net work display to ( no accosing network)

sony ericsson k770i keypad solution

This is usually a software issue on K series Sony Ericsson Handsets, try using the Sony Ericsson Update Service to Update or Re-Install the phones firmware... Its available to download from the Sony Ericsson support site if you dont already have it http://www.sonyericsson.com/cws/support/phones/k770i?lc=en&cc=gb Remember though if your phone is unlocked, the unlock for these may have been a Flash Patch unlock so you might have to get it unlocked again afterwards...

you can to apply unlock patch,but first you have to access patching. how to patch. http://www.akshayy.com/sonyericsson/tutorials/applying-patches-for-db2020-phone/
you must read carefully and apply only the patch with the same firmware of your phone firmware.If it is happen to patch not the same firmware just remove the patch. it will return to the state before you patch a wrong patch.

http://www.topsony.com/forum/patches-scripts-f36/w610i-r6bc002-40-patches-t7560.html
patch for firmware r6bc002..
there are lot of patches in there.
credit to the authors.
Do it by your own risk. i already explore a lot with my 2 w610i.
Let me know if u have question.