Sony RM-VL1000 stopped working

Hi, you can order a new RRMCGA759WJSA from Replacement Remotes. or you can order the keypad repair kit from replacement remotes to fix your keypad problem. You need the solution that is sold in the kit to fix the rubber keypad for those buttons.

Codes for Sony TV are: 0028/0119/0126/0127/0128/0129/0130/0182/0199/0228/0260/
0013 0002 0071 0380

open the remote control and clean the keypads from dirty, corrosion, oxide, and bad contacts, with c. cleaner very well. with carefully.
2) replace a new battery with the same type:alkaline
3) clean the contacts batteries with c. cleaner
4) try again.
5) if the problem persist you have 2 options go to repair shop TV for fix it, or REPLACE IT.
God bless you

Sansui is built by Japan firm Orion try 135 or 136 four digit try 0135 or 0310
On the remote control, press and hold the RM SET UP button.

1. While holding down the RM SET UP button, press and release the A/V I/O button.
2. Release the RM SET UP button.
3. Press the input (component) button to be controlled. NOTE: To program a television press the TV I/O button.
   
4. Press the number buttons to enter the numeric code corresponding to the component and the make of the component to be controlled. NOTE: If more than one code number is listed for the manufacturer, enter one code at a time until you find one that works.
   
5. Press the ENTER button.

hope this helps

Found universal replacement remote for Viewsonic N2750 at Target for $15. Works perfectly. it's the Sony RM-V310A. Tried all 5 remotes from Walmart, none worked even though it said would work on back of packaging..Target has about 5 Remotes only this one worked. My original remote died after 2 years. ordered an original replacement. that one died after 2 years. They're ****.Manufacturer discontinued it. found one online for $50. Just get the Sony RM-V310A at target.

The Sony RM-YD029 Remote control will work with the Dish Network VIP722 DVR HD Satellite Receiver, but the Dish Network VIP722's Primary remote address must be set to 1.

The procedure below will allow Sony RM-YD029 remote control to operate Dish VIP722.

Using the Dish Network Remote Control -
1. Press menu 2 times to get to system info page
2. In the system info page the primary remote address is in a white box (bubble) followed by a Green TV (1)symbol that says IR and indicates you the channel your remote control one is configured. The Sony RM-YD029 will work when this primary remote address number (in the white box) is set to 1.

If the Primary Remote Address of your VIP722 Remote control 1 is not set to channel 1, here is how to change it:

1. While displaying the system info page, press and hold the SAT button on your dish network remote until all other modes are flashing, about 3 seconds.
2. then press the '1' button on the numeric pad of your dish remote
3. then press the '#' button on the numeric pad of the dish remote
4. then press the 'record' button (red dot button - stores setting)
5. At this point you should see a number 1 in front of the primary remote address on the dish system info page

Ensure you enter the corresponding IR code into your Sony remote control per the instructions in the manual or Sony's web site. My 722 works with Sony IR code - 01775.

Volume buttons on Sony remote will work on Sony TV only.

sony RM-VL600 remote, can be programmed remote to remote...I bought it, it works.

Either the channel up and down buttons have both broken (unlikely) or everything else is working except the remote is not telling the device you are controlling to change the channel up or down.

Since all the other buttons are working well, that also requires that the receiving end of the pair to be working well, thus ruling out problems on that end.

Solution: Reprogram your remote to support the appropriate channel up/down codes for your TV/Tuner in question.

I need the code for operating an emerson television