It says my signal booster is a BDA device, what does BDA mean?

DTC C1100 00: Brake Booster Vacuum Sensor Performance .
Do you know what the brake booster is ?
Circuit/System Description
The electronic brake control module (EBCM) provides a power 5-volt reference to the brake booster vacuum sensor. The brake booster vacuum sensor converts the change in vacuum levels in the brake booster into a voltage signal. This signal is sent to the EBCM. The voltage signal ranges, from 0.13 to 3.30 volts depending on vacuum levels. The low reference is the return side of the sensor to ground.
Conditions for Setting the DTC
?€¢
Voltage at the brake booster sensor signal output to the EBCM falls outside the 0.13 to 3.30 volts range for more than 200 milliseconds.

?€¢
The power 5-volts reference is shorted to ground or battery positive.

Action Taken When the DTC Sets
The red BRAKE Warning indicator turns ON.
Circuit/System Verification
DTC C1100 will set as result of power brake booster vacuum sensor or circuit failure, test for power and ground circuits to the EBCM.
?‡'
Repair the power or ground circuits.

do you know what

1) Innovatiview

2) cellsignalboosters

Innovatiview has been manufacturing and supplying boosters for past 4 years and they offer fast and reliable service.There are not many reliable booster providers in the country. Boosters are complex devices that require specialization to manufacture and to install. Moreover, they are operator specific (eg. Aritel has different booster and Vodafone has different) and only a technician can install a booster. But they are easy to operate and can solve the problem of low network coverage easily.

Visit: www.innovatiview.com

you don't need a signal booster. Instead what you need is a WIFI signal repeater. This device basically captures your router's signal and repeat it to other devices. Basically place is somewhere between the router and your computer.

There are many out there but here's a cheap one on ebay

http://www.ebay.com/itm/like/122201090687?lpid=82&chn=ps&ul_noapp=true

I have Windows 7 64-bit and couldn't install TotalMedia 3.5 It would only get as far as Select Video Device, and give 2 options: > WinFast DTV Dongle Gold BDA Filter > FM/DAB Dongle I downloaded a driver (AF9015 BDA Driver - 9.6.3.1) from http://www.unisupport.net/ Select Video Device then gave these 2 options: > AF9015 BDA Driver > FM/DAB Dongle The first one did the trick. (The second one was possibly there because I have a Kaiser Baas USB FM radio.)

well unless ur house is 300 ft long or tall u shouldnt need a booster the wireless range of those routers are excellent

the usb adapter isnt a signal booster its a wireless device that receives/transmits the signal to and from the router

did u install the drivers for the usb device does it show up in ur network connections

There is no BOOSTER to do it,but you can do it for a router.Depends on your route rmodel there is several router signal boosters online.

Shopping results for wireless router signal boosters 3 pack Wi-Fi Wireless Antenna / Router Signal Booster

4 reviews - $10.02 - Amazon.com 2 pack Wi-Fi Wireless Antenna / Router Signal Booster
$7.99 - Buy.com 2 Pack Wi-Fi Wireless Antenna / Router Signal Booster
$8 - 2 stores

You answered the question in your question.
''weak signal' means exactly that, however it can also mean the signal is too strong.

If you have a booster installed into the ariel remove it, if not, try one. Make sure the TV is directly connected to the ariel, not via a DVD recorder or any other devices which require an ariel input.

Sony tv's have very sensitive tuners installed so its just a case of making your aprticualr settings compatible.

Check signal strength over at www.digitaluk.co.uk

Thanks

error 203 means , no change detected by the level switch when draining . possible cause
1, booster pump faulty
2, booster pump plug connector loose
3, start capacitor faulty
4, plug connector loose
5, boiler level switch faulty
6, no boost pump signal to- i/o pcb
7, no "boiler full" signal from i/o pcb check booster pump/ s2with manuel control

the most lightly or most common is the level switch in boiler tank will need changing

Booster will only work along with access points in your case the belkin wireless router - you have to connect the device to the router not to the windows xp pc

if you know how to configure and the device are compatiable to each other and allows bridging or can configure as your access point client then you need not wanna to get it connected via wire or T568b standard ethernet cable otherwise you have to connect with this cable will enchance the wireless activity

Wireless signals can go down its strength by any magnetic activity, oscillations such as microwave, powerful steel/metal frames and check your anteena position keep in different direction and check your pc wifi signal strength.

Interlink between your router and booster with utp cables gives you steady flow of data and full band strength.

Aviod using two company devices change the router to Hawking
Thanks Hothawk

The blend door is stuck or not receiving the control knob information to change the temperature.

Your car uses an electronic blend door actuator. you will need to locate this devise under the dash. You may have to remove the dash to get to it. You will want to make sure that there is power coming in to the new switch and going out to the Blend Door Actuator. If you do not have power to the switch then find out why and fix the broken wire, if you have power to the motor but it won't move then replace the Blend Door Actuator (BDA).

Make sure the black wire to the BDA is grounded. The do the following:
Test the orange wire going to the BDA and the Yellow wire from the BDA to the switch for postive power. This will tell you if the BDA is getting power in from the car and out to the switch. Then make sure you get a power reading from the Red with White strip and the Red with Lite Green strip, this will tell you that the switch is sending the power back to the BDA to control the temp. If power is coming in to the BDA and not going out to the switch then the BDA is bad. If power is going to and from the switch back to the BDA then that also says the BDA is bad. If the ground is broken that will cause the BDA not to respond.