Question about Dell PowerEdge Computers & Internet

Open Question

I reset the bios of my dell poweredge sc1430, and after that i can't boot

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: PowerEdge 2600 does not boot up ?

this server is a compleate wast of time trust me

Posted on Jan 18, 2008

Ad
  • 13 Answers

SOURCE: DELL Poweredge 2600 Bios FREEZES After Cpu check and before SCSI Drives check HELP!!!!

The BIOS check can freeze for many reasons.

Can you tell me if this is an existing system that was working fine and then had this problem, or is this a new (or new to you) system?

Can you give more information on what is actually showing on the screen?

Posted on Nov 06, 2008

  • 13 Answers

SOURCE: I changed the boot order

F12 is the Dell boot menu key.

Posted on Dec 16, 2008

  • 22 Answers

SOURCE: Reset Bios Password on a Dell Poweredge 2850

The following information was found here http://www.darklab.rutgers.edu/MERCURY/t15/pe2850dell.html

This should take care of your issue.

15e6a79.jpg
Password Jumper Place the jumper on both pins to enable the password. To disable the password, remove the password jumper.

Posted on Apr 06, 2009

  • 5 Answers

SOURCE: Does Dell PowerEdge 4600 Server support DVD ROM

I am working on one of these now and yes, it should boot from DVDROM. Be aware that it is a notebook style drive and there are no onboard IDE or SATA controllers, so once the drive dies you're in for a wallet hit. Same goes for the floppy drive which is integrated with the DVDROM. Even worse, the presence of the broken floppy usually means a USB floppy drive won't help when loading windows drivers at install time.

Posted on Jun 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Configure Dell Poweredge T300 to boot from optical drive


BIOS must see the optical drive. Re-seat / attach drive if it does not. The other option is to use another drive.

Jan 09, 2013 | Dell PowerEdge T300 Server

1 Answer

PXE-E61 failure while booting Dell poweredge 2900 server


Its a Network boot process ( Earlier Boot Rom ) Disable in BIOS setup or Ignore it, install OS and use server.

Apr 06, 2012 | Dell POWEREDGE 2900 Server

1 Answer

DELL POWEREDGE 6400 IS NOT BOOTING FROM THE CD


Hello,

Go to your BIOS and change the boot sequence so that the system boots to the CD 1st. (You should see a tab or label that says Boot Order or Boot Device.)

Good Luck
C2S

Aug 13, 2010 | Dell PowerEdge 6400 Server

1 Answer

Dell poweredge 2600 server recently display a message " No boot device available Press F1 to reboot or F2 to setup" Please why?


Did you experience a power event? Go to BIOS (F2), and make sure that RAID is Enabled. If RAID got turned off (power event, BIOS reset), then it will give you that message. If RAID is already enabled, then you may need to repair your operating system. If something else happened (drive failures, drives removed, etc.), then the array may be completely gone. Call Data Recovery services if it is critical you retreive the data.

Aug 03, 2010 | Dell PowerEdge 2600 Server

1 Answer

Dell poweredge 4300 Bootup problem after replacing cmos battery


Look for a jumper on the motherboard where it would allow you to clear the cmos. basically you would move the position of the jumper and turn on the computer and let it clear itself.

Then after it clears turn off the machine, put the jumper back into its original position and then turn the computer on and see if the message goes away.

Also go into the BIOS and put in the correct time, date, year, etc.

Aug 16, 2009 | Dell PowerEdge 4300 Server

1 Answer

Can not boot dell poweredge from usb cd


try turning usb support on in the bios,if this doesnt work try reseting your bios this should return it to default,hit f2 as it restarts when you are in. hit alt e alt f it should beep everytime you do this,what this basically does is clears nvram, go to boot devices and see what you have available,exit and retry your boot device

Mar 23, 2009 | Dell PowerEdge 2650 Server

2 Answers

PowerEdge 2600 does not boot up ?


you need to set the boot device order. Usually F12.
or you can go to bios with F2 or F10.

your cd-rom is wrong you need the Instalation and Server Management CD. I think it's possible to download this cd at their site.

good luck

Dec 03, 2007 | Dell PowerEdge 2600 Server

2 Answers

Dell PowerEdge 6300 Server Hangs after A13 Bios Upgrade


I know this sounds simple but did you reset the BIOS by jumping it after pulling out the motherboard battery?

Nov 06, 2007 | Dell PowerEdge 6300 Server

Not finding what you are looking for?

Open Questions:

Computers & Internet Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...