20 Most Recent Dell PowerEdge 2650 Server Questions & Answers


It might not be a driver. It might be the monitor. Try another monitor.

Dell PowerEdge... | Answered on Apr 14, 2018


download dell server assistant onto a cd... youll get a menu, follow the menu. you also need the server 2003 installation cd

Dell PowerEdge... | Answered on Aug 19, 2012


First - re-seat the harddisk and reboot the computer. If this does not work then reboot and go to theBIOS configuration to see if the BIOS detects the hard drive. If it doesn'tdetect the hard drive then it could be faulty. Next - to determine if thehard drive is faulty, remove the hard drive and insert it into an USB hard drive adapter and connect it to a workingcomputer's USB port. If this computer cannot see itas an external hard drive and you cannot open the various folders and files,this confirms the hard drive is faulty. The hard drive needs to bereplaces in the laptop and Windows installed and the laptop's device driversand your programs etc to get a functioning laptop again.

Dell PowerEdge... | Answered on Aug 19, 2012


Hello, Not sure what the media type is but I will assume you mean a tape drive as you are able to switch between write protect and writable. At the boot of the tape cartridge you should find a button that moves from side to side. You should be able to see "write" on side and when you move the switch you should see "Protect". If this is not the media form you are usings, repost with what type of media you are using. Good Luck.

Dell PowerEdge... | Answered on Feb 23, 2012


Hello,

Be sure to check your cable connection both at the drives and the motherboard. You may have to swicth then out with known good cable. If you do use new cable and get the same results, you may have a bad hard drive. Also, after checking the cable connection, recheck your BIOS setting to make sure the system 'see' the hard drives.

Good Luck.
C2Solutions

Dell PowerEdge... | Answered on Oct 09, 2011


Hello,

There could be many things that could cause your halt problem. From my experiencew ith servers the first thing I would do is try resetting your BIOS setting to default. Also, reset the jumpers to clear out the CMOS and retry your install.

Keep us posted. Good Luck

C2Solutions

Dell PowerEdge... | Answered on Jun 11, 2011


Try entering the BIOS (usually by hitting F2 or Delete during the boot up sequence) and looking under the boot menu for the USB drive. Some older systems cannot boot from USB. You might have improperly formatted the USB drive. What are you trying to boot into?

Dell PowerEdge... | Answered on Feb 28, 2011


try turning usb support on in the bios,if this doesnt work try reseting your bios this should return it to default,hit f2 as it restarts when you are in. hit alt e alt f it should beep everytime you do this,what this basically does is clears nvram, go to boot devices and see what you have available,exit and retry your boot device

Dell PowerEdge... | Answered on Feb 25, 2011


Hi Dell poweredge 2650 dosent support usb boot
try using a CD or DVD or floppy if you can get 1 big enuf

Dell PowerEdge... | Answered on Dec 27, 2010


how is the boot order set in the bios ?

try to set cd/dvd drive first

Dell PowerEdge... | Answered on Dec 27, 2010


Hello, You should be able to get into the bios and reset within.
Failing that .... power off the unit. Disconnect the servers power supply cable. i.e. make sure it is not connected to mains power. remove the covers. on the motherboard is a cmos battery .... remove it. wait a few minutes for the cmos to drain.
perform the reverse of the above.
when you poweron ... the date time will need to be reset. cmos password should also be reset.

Dell PowerEdge... | Answered on Oct 13, 2010


Unfortunately, the 2650 cannot boot to USB devices. Try PXE if installing an OS.

Dell PowerEdge... | Answered on Aug 19, 2010


This can be done with hardware or software.

Hardware: find and remove the CMOS battery

Software: buy a bootable program that will allow you to remove the password

Dell PowerEdge... | Answered on Aug 18, 2010


you will need to download the RAID drivers from the Dell website
http://support.dell.com/support/downloads/download.aspx?c=us&cs=19&l=en&s=dhs&releaseid=R74082&SystemID=PWE_PNT_P3C_2450&os=WNT5&osl=en&deviceid=1374&devlib=0&typecnt=5&vercnt=7&formatcnt=2&fileid=126163 and load them onto a floppy drive.

Then when installing the server press F6 to install other drivers this will load the PEC drivers and W2k3 will then see your drives

Do not try to load the drivers from a USB as W2k3 is "preset" to only accept drivers from a floppy drive unlike WIndows server 2008

Hope this helps


Dell PowerEdge... | Answered on Jul 23, 2010


Hello,

Yes, Server 2008 will install on the 2650 as long as you make sure you have enough RAM and hard drive space. Once you have Server 08 installed, you will have a to-do list to help with setting up hyper-v.

Good Luck
C2Solutions

Dell PowerEdge... | Answered on Mar 05, 2010


ERROR 02A2: BMC System Error Log (SEL) Full
press F1 to continue or F10 to enter BIOS.
I wait for 2 minutes without doing any thing my server get started normally.
Please help me how to stop this error

Dell PowerEdge... | Answered on Feb 21, 2010


Hi there, as per your information, i can say that the device driver missing from your system. Just install the driver again & restart your System . Then try it.Thanks & waiting for your feedback.

Dell PowerEdge... | Answered on Feb 19, 2010


Process of elimination? I first thought it may be a power problem but I could not understand the LED flashing (It still maybe a power problem) If you can leave on charge for 4-5 hours more if you can make sure the light is not flashing (That is turn the laptop off at the power switch) Try turning on after being on charge for as long as you can If that does not work it may be the bios with the wrong setting or the Hard Drive is faulty (The more I think about it I think it may the the last issue) Try the other steps first the turn on holding the DELETE button it (I think that is the button to access the bios ) This with work if the Hard is Good or bad)

Dell PowerEdge... | Answered on Apr 22, 2009

Not finding what you are looking for?
Dell PowerEdge 2650 Server Logo

30 questions posted

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

PowerEdge Dell

  • PowerEdge Dell

Most Popular Question

install hyper v dell 2650

  • Computers & Internet
Loading...