20 Most Recent Everex StepNote NC1502 Notebook - Page 2 Questions & Answers

u can make ur computer as new as it was....just follow the procedure detailed in my website
Format Disk Page in there...gives full details
www.sureshayyar.110mb.com

all the best
leave a feedback of how u did ?

ok, the screen going blank may be your inverter going bad. i do not know about the wireless issue. and the sluggishness of windows is due to the fact that your computer isnt really powerful enuf for vista.

you should have a button F2. if you push the function button located at the bottom left hand side next to the Ctrl button and press F2 that should turn it back on.

you may want to make sure it is not the power cord first, i thought mine was the power cord, I plugged it up to a different laptop and it worked. so it is something in the laptop..

Download the user manual from Everex:

http://www.fic.com.tw/everex//us/support/nc150x/nc150x.php I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

my guess this is the blue screen of death...you will have to re-install your operating system. Hope it was backed up!

Is your "2GB upgrade" one memory-stick, or two?
If it is one, then it's possible that the motherboard does not support so much RAM on one stick.
If it is two, then remove one stick, and try.
If it still fails, then remove that stick, and try the other stick.
If it still fails, then try your original 512KB stick.
If it still fails, then try your original 1GB stick.

probably itz either minor case of software corruption/improper ground/cpu fan..
or major case of faulty or defective main board/ram/daughter or addon card(s)..

..plz do check the following as in order:..
the Hardware part:..
1)a)in power on mode, open/unplug the data/vga cable of the monitor from cabinet..see if raster or 'osd' is appearing on the monitor screen..if so monitor is ok..else replace the monitor and see..[not applicable in case of laptop]..
b) in case of laptop try to get output from external display unit/monitor using vga port..if there's proper display in there..the problem is probably with either the 'lcd' or 'ccfl' or 'inverter circuit'..

2) if u hv a graphics card, replace with a standby or onboard and see..[not applicable in case of laptop]..

3) unplug mains supply..pick open/remove the cmos battery..check (above +3v)..resit..

4)see if the ram(s) is loose/faulty..open clean/remove carbon & or oxide formed on the teeth with an eraser n resit it..or replace with a standby n see..

5) a) see if ur hdd is noisy or emitting any 'ticking' noise (like 'tuk tuk' or 'kirr kirr')..
b) or if the system is not supporting either the newly installed device or itz software/driver /firmware
if so, u need either a fresh os installation or ur hdd is likely to b replaced..

6)remove/clean dust neatly..dust is non-uniform in nature n may cause jam/short circuitry/excess resistance n many more..resulting an increase in heat..

7) open the CPU Heat-Sink with fan out of the socket..put some "Heat Sink Compound" (available in local electronics chip level spare market) between the cpu/processor and the CPU Heat Sink *** fan..resit/fit it tightly in position..

8)on main/mother board..see with a debug card for mb error..may b short..look for defective capacitors(esp above1000mfd)/mosfets..go through the mb's south bridge n the circuit lie around atx connector..the crystal clock generator (if cpu isn't heating up)..

9) [in case of desktop] the smps itself may b defective/faulty..check the outputs of smps viz. 0v (black~ground); +12v (yellow); +5v (red, green~ps-on, violet~pg& grey~sb); -12v (blue); -5v(white); +3.3v(orange)..the 'oscillator and error amplifier ic', or pwm switching regulator circuit..look for defective protector-transformer/resistance(esp 4.7k)/mosfet..
check the battery n adapter [main power], in case of laptops..

if u r bot a professional, always better to seek advise from ur system admin/vendor....

Based on the web site it looks like your OS is VISTA. go to help and type in "wireless network" this might get you to a help page that can walk you through how to turn on radio. I know this is vague but I am not that familiar with VISTA yet. I know in XP i would go to "Control Panel" > "Wireless Network Setup" this opens a wizard that steps you through starting your wireless network.

I Hope this helps some.

GOOD LUCK!!

Your driver may have seen it's best days. If you have another computer that you can use the part from to make a test that will verify it for you.

go find your rescue disc or just reinstall windows the info on the hard drive is gone but if you want to pay it proably can be somewhat retrieved by an expert computer lab

look around ur laptop, there should be a button key or a switch 2 turn it on. if look on the bottom right on ur taskbar, there might be an icon for ur connections e.g. bluetooth, wlan, wi-fi etc. see if u can switch it on from there. if u still can't do it take ur laptop 2 a pc world center and they might be able to help u. i hope dis helped =)

Hi,

On your Everex laptop look at your keyboard and press the following>>>>


FN + F2 they both have blue symbols on them.

Your wireless radio should now turn on and detect your wireless network.


Regards.

Make sure it is getting enough airflow underneath. Laptops generate a lot of heat that must be removed.

try control panel in power options
advanced tab, look for a standby box with a time set on it, change it to never

Go to driverguide.com or to acer.com and have them email the driver to you or tell you wher to find it.