20 Most Recent
Riccar 8955 Upright Vacuum - Page 2 Questions & Answers
I need to replace the belt on my Riccar supralite
Lay the vacuum upside down, remove the bottom plate, remove the brush roll and belt, install new belt around motor shaft and brush roll, pull on brush roll to stretch belt far enough to drop brush roll back into place.
Not picking up. No suction
Make sure good suction at the end of hose and no clogs in tube hose goes into at bottom of vacuum. If good make sure belt is new and brush roll spins fast when lowered onto carpet. It may need clutch adjusted or rubber pad replaced.
Low suction
REplace the filters and belt. If it's been a few years since it's been serviced take it to your dealer. The 8955 can work properly for many years but there are some things that will need cleaned and service to work properly.
The switch will not turn the vaccum off or on
The switch is activated by the lever you push in the handle. Start by tightening the screw holding the handle in. If that doesn't solve it remove the bag door and the screws holding the cover above the bag to gain access to the switch compartment. If you can't figure it out in there take it to your Riccar dealer
Need to clear blower in 8850 model vacuum
Unless you have removed the plastic guard under the motor filter it is impossible for the toy to have lodged in the fan. The toy would have to go through the bag, through the motor filter and through the guard before it could reach the fan.
How to change belt of riccar vacuum rsl3
Remove the bottom plate after laying the vacuum upside down, make sure it's not plugged in first. Pull the brush roll out of the nozzle housing, put the new belt around the motor shaft and then the brush roll, pull on the brush roll to give you enough leverage to install the brush roll back into place, reinstall the bottom plate.
Riccar 8995 no suction
If it's been over a year since you've replaced the belt that is the first place to start. Stretch belts lose elasticity and will still turn the brush roll but when the brush roll is lowered to the carpet it may not turn fast enough to pick up properly. If you have good suction at the end of the hose check to make sure there is not an obstruction in the tube where the hose goes into the bottom of the vacuum to the brush roll. Make sure your filters are replaced at least once per year and the bag is not full or has a lot of fine powder dust in it which can clog the bag.
Riccar vacume lite for bag is on when bag is not full
sometimes that can happen if the pores in the bag are clogged, as might happen if you have been vacuuming very fine dust like wallboard dust. this means that the bag might be functionally full, even though it still appears un-full. also, check the hose for a clog, because that can also give a false indication light.
Why does the riccar vacuum reset button not depress?
In my experience the Riccar requires reset when it has ingested something that jams the roller such as the fringe of an Oriental carpet. Be sure to clear any such obstruction, then I use a ball point pen to press the button. It does not move very far to accomplish a reset.
How do I change a
Lay the handle back, release the two tabs. Holding the filter cover to access the filter.
I have a riccar vibrance red vacuum, just
The reset button only pops out if the vacuum motor overheats. It does not affect the brush roll. If the motor is running the problem is most likely a broken or stretched belt.
Need to replace brushes ona ricca 8955
Your model can last well over 20 years. You might be able to change. The. Brushes yourself but there are adjustments that are difficult to do properly by the average homeowner. It. Would be best to talk to a qualified. Riccar repair technician before you attempt to change the brush strips.
Smells like burning rubber when running
Vacuum belts lose elasticity and will slip. It may spin the brush roll ok when you look at it but be so loose that when. Vacuuming carpets the belt will stop turning. The motor shaft is still spinning and will melt the rubber belt causing a burned rubber smell. Belts on almost All vacuums need. To be changed at least twice per year.
Sock stuck
About the only other place it could be so in the tube in the power nozzles which can be removed. Take off the bottom plate to access this area.
How to replace the hepa filter on a riccar vacuum # 8995
Remove the filter cover by releasing the two latches. If it's been a long time since you've removed the cover it may be difficult to get the filter to release. The filter should be changed once per year for the average homeowner
Not finding what you are looking for?