Top 20 Uniden DECT 2080-5 Quint Phone Questions & Answers

Can you adds some more information. What do you mean it's on hold? Can you receive calls? Is there more than one handset? If so does the problem appear on all handsets? Try resetting by taking out the battery for a few minutes.

See page 32 of this manual: http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DECT2080-2om.pdf

Follow the instructions on page 40 of this manual.

You may download a copy of the manual here.

how do you set up the answer machine on dect 6.0 uniden? the machine shows on , but all you hear is a noise.

If you mean muting/unmuting the microphone, press the mute button (above and right of the cursor pad. If you mean the ring volume,press up-arrow while the phone is idle.If you need a manual you may download a copy here.

Follow the instructions on page 32 of the manual to adjust the volume.

You may download a copy of the manual here.

Hold the "Silent Button" down for a while. It is shared with the # key.

The reset instructions for the 2080 are on pages 48 and 49 of the manual.

Silent Mode
You can silence the ringers on the base and all handsets for a specific period of time; the answering system answers any incoming calls without playing anything through the speaker.
With the phone in standby, press and hold # on any handset. The phone prompts you to select the number of hours (1 - 9 or Always On) that you want it to stay in silent mode.
To confirm, press # or just wait about 5 seconds. The phone turns on the answering system and displays Silent Mode On on each handset.After the selected number of hours, the phone automatically exits silent mode. To exit silent mode manually, press and hold # again.
If the phone is in silent mode and you turn off the answering system, the phone exits silent mode.
Multihandset Features To use the features in this section, you need at least 2 handsets.
Your base supports a total of 12 cordless handsets: the one that came with the base and up to 11 DCX160 accessory handsets.You must register accessory handsets to the base before using them. (Handsets that came packaged with the base are already registered.)Handsets that aren't registered display a Not Registered message. For registration instructions, see p. 18, or see the accessory handset manual.If a handset was ever registered to a base, you must reset it before it can register to a new base; see p. 18, or see the accessory handset manual.Conference Calling
When an outside call comes in, two handsets can join in a conference call with the outside caller.
To join a call that's already in progress, just press Talk/flash or SpeSpeSpeaker.To leave the conference call, hang up normally; the other handset remains connected to the call.

To turn off silent mode, press the "#" and hold down until it changes. :)

Hi! Some phones have a double function for the "#" key. Just press and hold this button "#" and the silent mode will turn off/on.
I hope this will help you! Have a nice day!


*please don't forget to rate my services :)

You can download the manual from the manufacturer's web site at
http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/TRU8885-2om.pdf

http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DECT2080-2om.pdf

Activating Personal Ring
You can assign special ringer tones to anyone in your phonebook. When your phone gets a call, it looks up the Caller ID information in your phonebook. If you've assigned a personal ringer to that number, the phone uses it so you know who is calling. To turn the personal ringing on or off, follow these steps:

1. Press [Menu/Select]. Select the HANDSET SETUP menu, and then the PERSONAL RING submenu.
2. Move the cursor to select ON or OFF.
3. Press [Menu/Select]. You will hear a confirmation tone.

Selecting a Ring Tone (Handset only)
You may choose from four melodies or three tones for your phone's primary ring tone. Each handset can use a different ring tone or melody. The available ring tones are as listed:

1. Press [Menu/Select]. Select the HANDSET SETUP menu, and then the RINGER TONES submenu.
2. Move the cursor to select a ring tone. As each ring tone is highlighted, you will hear a sample.
3. When you hear the tone you want to use, press [Menu/Select]. You will hear a confirmation tone.

Adjusting the Speaker Volume
Handset Speakerphone: You can choose from six volume levels for the handset speakerphone. To adjust the speaker volume while on a speakerphone call, press the UP Arrow button (to make it louder) or the Down Arrow button (to make it softer).
Base Speaker: You can choose from ten volume levels for the base speaker. To adjust the speaker volume while call screening or playing messages, press [volume +] (to make it louder) or [volume -] (to make it softer).

Adjusting the Audio Tone
If you aren't satisfied with the audio quality of your phone, you can adjust the Audio Tone of the earpiece while on a call. Your phone gives you three audio tone options: low, natural and high; the default setting, Natural Tone, is recommended for hearing aid users. Audio tone adjustments only apply to the earpiece, not the speakerphone.
To adjust the audio tone:

1. While on a call, press [Menu/Select].
2. Move the cursor to select AUDIO TONE, and then press [Menu/Select].
3. Move the cursor to select desired option (HIGH TONE, NATURAL TONE, or LOW TONE), and then press [Menu/Select]. Selected option appears in the display for two seconds, and then the display returns to normal.

Deleting Phonebook Entries
You can delete a single phonebook entry at a time or all phonebook entries at once:
To delete a single phonebook entry:

1. When the phone is in standby, press the phonebook key.
2. Find the entry that you want to delete and press [Menu/Select].
3. Select DELETE. DELETE ENTRY? appears in the display.
4. Move the cursor to select YES.
5. Press [Menu/Select]. You will hear a confirmation tone, and DELETED! appears in the display.

Deleting Caller ID Numbers

1. To delete only one Caller ID number, press the Caller ID button when the phone is in standby, and then find the number you want to delete.
2. Press [Menu/Select] and select DELETE ENTRY.
3. When the phone asks you to confirm, select YES.

1. To delete all the Caller ID numbers, press the Caller ID button when the phone is in standby, and then press [Menu/Select].
2. When the phone asks you to confirm, select YES.

Note: When you delete a Caller ID number, you delete it permanently.

Deleting a Redial Record
If you want to delete a phone number from the handset's redial list, follow the steps below:

1. When the phone is in standby, press [Redial/Pause].
2. Use the UP Arrow button and the Down Arrow button to scroll through the redial list.
3. When you find the redial number you want to delete, press [Menu/Select] and select DELETE ENTRY.
4. When the phone asks you to confirm, select YES. The redial number is deleted.

Resetting the Voice Message Waiting Indicator

1. When you receive a new voice mail message, the new message LED on the top of the handset flashes and VM appears in the handset display.
2. In the event your message alert tone gets out of sync with your phone company's voice messaging system, you can reset back to its original "no messages waiting" state.
3. To reset, press and hold [find hs] on the base for five seconds.
4. A beep sounds and the message alert tone is reset.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Hi,

You can download and print the instruction manual in PDF format by clicking this link.

Please note: Adobe PDF Reader is required to view this manual. Click here to download the latest version of Adobe Reader.

Hope this solves your problem. Thanks for using FixYa.