Belkin (F5D7633UK4A) Wireless Router - Answered Questions & Fixed issues

http://cache-www.belkin.com/support/dl/p74730uk_f5d7633_man.pdf?_ga=1.21314739.96199321.1451713082 That link is for the owners manual that can walk you through it and then below is a video I made of setting up my F9K1003V1. Process should be same but menu may look different.

You can adjust MTU from within the Belkin Router administrative console. You really should not be changing it unless your current ISP gives you a specific MTU setting, otherwise you could disrupt internet connectivity.


Default IP address: http://192.168.2.1
Default admin username: Administrator
Default admin password: <blank>
Be sure to set a password for your router!

This is the address where you change MTU
192.168.2.1/wan_pppoe.html


Belkin Wireless G User Manual:
http://www.belkin.com/support/article/?lid=en&pid=F5D7230-4&aid=5999&scid=221



Windows Tools to adjust MTU:

DrTCP tool:
http://www.dslreports.com/drtcp

TCP Optimizer
http://www.speedguide.net/downloads.php

were you able to connect to that router before? If not then do the manual checking of wireless settings, get you default gateway ..how? http://www.ehow.com/how_2091470_computer-ip-address-windows.html instead of looking for Ip address .. look for default gateway it should be after subnetmask or if you havent change any settings on your router if the default gateway should be :192.168.2.1 -then open any of your browser like internet explorer or Firefox and type in the default gateway in the address bar (make sure during these steps your computer is currently connected to the router hardwired) -Do the wireless settings, here's how: http://en-us-support.belkin.com/app/answers/detail/a_id/3774/related/1/session/L2F2LzEvdGltZS8xMzA5ODU1NTc5L3NpZC84a1NuZ2N5aw%3D%3Da also what is your OS is it XP or windows 7, as well as check you wireless capability on your computer if it is ready for wireless connection...

Here you go: http://www.belkin.com/support/dl/p74559-a_f5d7230-4_man_6-04.pdf

VPI and VCI codes are for broadband ADSL connections check this page out to see the numbers you need to set up, you also have to configure the encapsulation type according to your country's service, the encapsulation type is usually in the same settings page where the VCI and VPI settings are.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

do you forget your password or what well try either of thesee. hope it works

1. Connect the computer to one of the four LAN ports on the router.
2. Open a web browser on the computer.
3. In the address bar of the web browser, type http://192.168.2.1
4. Click Login in the upper right-hand corner of the page. The router does not ship with a password, so just click Submit.

Click on System Settings under Utilities on the left-hand side of the opened page

1. You will see a feature called, "Administrator Password". Type in your current password
   

2. Click "Apply Changes". Your new password is now active.
   

Do not forget the new password and keep it somewhere safe. If you forget your password, you'll be unable to access your router's settings. If you forget or lose your password, you'll need to perform a hardware reset on the router. This will reset the password to its default, as well as erase any and all other settings you may have changed.

When you purchased the router, you should have configured the wireless interface:
* set a SSID, a "name" for your wireless network,
* an encryption-level. Hint: use WPA or WPA2
* a password for your wireless network.

Do that, and then use the SSID and password on your Internet TV, to connect to your network.

Hi,

Welcome to Fixya. If you want to secure the network you all you need to do is to access the router settings page and put a security either WEP, WPA or WPA2 and a Network Key or Passphrase.

To access the router page you need a working computer that is connected to the router. To access the router page just open a browser then type 192.168.2.1, the Default password is blank

Click on Security under Wireless, Select WEP, WPA or WPA2 and personalize a Security Key or Network Key (Passphrase). Security Key serves as a password on the network.

If you have questions please let me know. Thanks for using Fixya.

You may need to reset your router by pressing the reset button (usually a very small hole in the back) then you can log in using the default password/username.

For Most of the Internet Connections the VPI is 8 & VCI is 38. But it Depends on your internet Service Providers...

I have the same router; Do you get this error while you are trying to connect to your router from your PC? Or during setup of the router?
Please clarify, so I can help you better.

Is this a cable service?
It is possible you have a bad connection. Either inside the house or outside.
Cable.. You will have a cable modem connected to the cable.
One main thing to do is to re-trim all the ends of the cable at every connection point between the modem and the outside connection. Replace any old connectors or splitters with new ones of correct value. The idea being to remove any oxidation which will impair the signal. If none of this helps, you may need the outside wiring looked at. Your connection service should do this at no charge.
If you have not done so, power off the modem completely, including removing the battery back up.
Wait about 20 seconds. Reinstall battery and power connection. About 20 -30 seconds to reconnect.
"few hours everyday" might indicate a problem outside, (wiring or junction box) possibly warming up in sun and cooling later?
On the PC. Use the connection wizard to "connect to a network". Connect to your own network on every pc you use.

Hello,
There are many reasons why this might be happening.. You could try the following steps..
1) Disconnect the power from router for a minute and reconnect and check. 2) Try changing the wireless channel and Network name and try re-connecting. 3) Check if there is an firmware update for your product and update if any update is available. 4) If none of the above steps work you will need to reset and re-config your router. ( For that you need the CD given with the router and you will need the ISP settings.)
Hope this helped

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

PS3 And XBOX :: BELKIN



Step 1:Connect Modem - Router - Computer (Wired)

Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3:On the Left click firewall

Step 4:Leave the Password blank and click submit

Step 5:Disable it and click apply changes

Step 6:Scan and connect in the Xbox/PS3/Wii

Step 7: Get the IP Address of the Xbox/PS3/Wii

Step 8:Open Router Setup in the Computer

Step 9:On the left under Firewall Click DMZ

Step 10:Enable the IP Address of the Xbox/PS3/Wii in it

Step 11:Click Apply Changes

Step 13:On the left Under Utilities click System settings

Step 14:Scroll down to the bottom

Step 15:Enable UPnP

Step 16:Click apply changes

Step 17:Test the connection ,Check the NAT

If working then let me know

======================================...
If it is still not working

Open Router setup

At the middle Under internet settings check the WAN IP

IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to bridge the modem


Regards
TOM

Do you see the network on the pc you are trying to access the internet from? If yes, then check to make sure the cable is securely connected from the router to the cable/dsl modem. Try to change the cable out completely if you can. You can also try to bypass the router to the computer to make sure you do have a signal coming in for internet. Try to reset the router and reconfigure it. If you on a loptop make sure you have the wireless on, some models you can switch wireless on and off and this will prevent you from accessing the internet.

Here is a great tutorial to Connect and troubleshhot your Xbox to a wireless network.
If you need more help post back! Thumbs and testimonial are welcome!

If your OS is Windows theres a good tutorial Working with Widows Wireless Networks

That can help you out to configure your wireless networks.

If you need more help post back!
Thumbs and testimonial are welcome!

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works


Regards
TOM