Roland VersaCAMM VP-540i - Answered Questions & Fixed issues


Could you try
(1) Temporarily stick a white strip over the sensor where it detects the media or
(2) On the length of the media or
(3) Even staple same sized white media below the black one which you can un-staple after printing.
kindly ignore if these are (s) tupid answers

Roland VersaCAMM... | Answered on Mar 23, 2016 | 217 views


Just one Question?
Do you have your LAN Cable tied with your AC power Cable?
I have th same problem on two VP540 after seven years of trouble free working. A few months ago I was reorganizing my shop and I tied up both cables to avoid tangle cables with machine wheels every time I move It.
I think that the noise produced by AC Voltage Affect the VP540 ethernet port.

Roland VersaCAMM... | Answered on Jan 13, 2015 | 1,478 views


Sounds like the motor is jammed.
This is a scan motor over current error where a large load is put on the motor movement instantaneously. Turn the power off, clear any media jam that may have occurred and turn the printer back on. If the error continues, please contact your local Roland Service Center.

Roland Office... | Answered on Aug 06, 2018 | 1,882 views


Turn the typewriter on while holding the CODE key down.

Office Equipment... | Answered 19 hours ago | 21 views


The Brother AX10 ribbon should fit it I have them

Office Equipment... | Answered Yesterday | 197 views


You did not post the make and model of the printer but the issue could be a driver on the computer. IT could also be bad ink/toner cartridges etc.

Office Equipment... | Answered 2 days ago | 46 views


12 steps to resolve this error:
  • Turn the printer ON
  • Now wait until HP printer get fully ready and turn silent
  • Disconnect the USB wire from both ends if connected any
  • Remove the ink-cartridges while the printer is ON
  • Now close the printer door and remove power cord from the rear, also remove it from power supply source as recommended by HP officials
  • Wait for couple of minutes before reconnecting it to power
  • Reconnect HP printer to power outlet and manually reboot it if does not come ON its own
  • Now wait until your printer completes its normal process of warm-up and open the main door to reinstall ink-cartridges
  • After completing the reinstallation of ink-cartridges, your printer may prompt to align or calibrate the ink system, if yes, then proceed with it
  • Now reconnect the USB wire if required, wireless printers will not require USB wire
  • Open HP printer application and try to print a test page

Office Equipment... | Answered 2 days ago | 325 views


120

Office Equipment... | Answered 3 days ago | 19 views


Make and model number may help you get an answer

Office Equipment... | Answered on Oct 11, 2019 | 22 views


All electrical medical equipment

Office Equipment... | Answered on Oct 11, 2019 | 16 views


actually this is a voltage error, but you can fix it by cleaning interlock switches, or replace it

Office Equipment... | Answered on Oct 09, 2019 | 581 views


You can get the manual on the link below. it does not give a factory default though. you will need to call 800-828-1438.

http://www.sentrysafe.com/pdfs/OwnersManuals/504154.pdf

Good Luck

Office Equipment... | Answered on Oct 07, 2019 | 2,321 views


methylated spirits is the best cleaner to use ( alcohol based cleaners )
sometimes if you load the pen and it is not full, tip the pen vertical active the plunger again the dip it back in the ink and do it again
That will ensure that a second go fills the pen properly

Office Equipment... | Answered on Oct 07, 2019 | 50 views


The scanning lamp (xenon tube) is faulty
https://mucinhanoi365.com/

Office Equipment... | Answered on Oct 03, 2019 | 21 views


Meet an engineer

Office Equipment... | Answered on Oct 02, 2019 | 20 views


Open the left hand top cover, In between the ribbon rollers you will see a small flipper, ( small piece of metal with a wheel stuck on one end. ) Maually turn this so the grey wheel is on top and white smaller wheel on the bottom.

This ocassional gets jammed and need righting manually.

Office Equipment... | Answered on Oct 02, 2019 | 208 views


Error code c - 3903 ??

Office Equipment... | Answered on Oct 02, 2019 | 790 views

Not finding what you are looking for?
Roland VersaCAMM VP-540i Logo

22 questions posted

Ask a Question

Usually answered in minutes!

Top Roland Office Equipment & Supplies Experts

JonSnell Electronic
JonSnell Electronic

Level 3 Expert

30506 Answers

Ravi

Level 3 Expert

1682 Answers

Are you a Roland Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...