Top 20 Lanier Ld328c Ld335c Ld345c Black Developer Unit - Page 9 Questions & Answers

Try this press the "yellow/ca" botton, then enter 1-0-7, then press and hold the "red" stop" till the display changes. Once, it changes turn the Main power switch OFF. Not the one on the control pannel. Let it power down then turn it back ON. If the problem is still there try to turn the copier Off again and unplug the sorter/ finisher and turn the copier back ON. Is the problem gone, if so you may have to get a service person come in and repair the sorter. Good Luck.....

LD unit problem, or laser sync detector....requires a tech for sure.

It's most likely your Laser diode (LD unit). You're going to require a tech...see the posts the following link for the same problem. It's for a Ricoh model, but your machine actually is a Ricoh Machine (Ricoh owns Lanier), and is virtually identical to this one -just a generation older.

http://www.fixya.com/support/t1936988-sc_326_322_329_in_af2045

The switch that detects the open cover is probably broken or stuck. Do this. Lean / press on the cover while trying to copy. Does it work then? If it does, you know for sure that the switch is stuck. If it doesn't, the switch is broken.

How to find this switch? Is there a small plastic tab on the cover that goes into a hole that you can see? Those are usually where the switches for such covers are located. Spray some electronic parts cleaner down this hole (available at auto parts stores). See if this helps any.

Bilal Hassan
Clarksville, MD

Try turning it off, then unplug it from the wall, wait 30 seconds, and plug back in, then turn it on and try to operate.

Hello sir; I believed you talking about LD045, am I right? In this model it doesn't have waste toner bottle, the only place you can clean is imaging transfer unit, after you cleanup the message will be disappear.

Put a piece of white paper behind transparent content. The more light that shines through when copying, the darker the copy. Hope that helps

"user tools"
"Counter"

send me an email address and i'll send you a copy

This means heater warm up was abnormal.maybe thermionic fuse to reset push the button top of fuse.

Are you sure about that model number? Is it a laser machine? Black and white or color? Do you have a serial number on it?

Well offhand, just try unplugging it for 30 minutes and plug it back in and see if it helps.

It means there is a paper jam in the machine.

Reboot the machine first. If that doesn't work, go to user tools - system settings - file transfer or interface settings (depending on the model) and enter and admin email address. Then go to admin tools and tell it to auto specify a sender. It is looking for who is sending the scan, not who is receiving it...

your printout is only 1/2 the page than your image may not be developed or transfered. you will need to remove the deveolper unit and look at the front of it. does the devolper go all the way across the front of it?

did you turn the dial to light the display? if so the back lights are out on the display or the ballest is bad. you need to replace the diaply. have a tech come out.

Goto my website and Download the file from the Public Folder. It is the only Point 2 Point in the folder.

Do not forget to vote Yes or No if this information was helpful


www.copytech21.spaces.live.com

It could be that the black developer unit is clogged. The toner low sensor is located in the black developer unit. A trained copier tech may be needed to troubleshoot this.

I had this problem with an Aficio 2018D using scan router ScanRouter V2 Lite. The MFP would say it couldn't update the delivery list. Deleting/Reinstalling SW, resetting the I/O device and so on, nothing worked. At last I had to use the SP 5845 (see maintenance manual) to manually change the Delivery Server IP address, which was initially set to 127.0.0.1 and had by then been corrupted to 0.0.0.0, to 192.168.1.227 which was the IP address of the WinXP where ScanRouter was running (of course port 3870/tcp must be opened as exception in Windows Firewall). The scanner immediately "saw" the delivery list, updated by itself and, touching wood, worked like a charm ever since.

I believe that model is a Richo in a disguise.... To get into service mode, first press the yellow C/A botton, then the numbers 1 - 0 - 7, then press and Hold the red C/Stop botton for a few seconds and the display will change. Then you are in the Service Mode... Good Luck

Should be as follows:
"User tools"
"system settings"
"key Operator"
"program/ change/delete address"
Then select the appropriate function /address, etc. to change

Please let me know