Top 20
Lanier Ld328c Ld335c Ld345c Black Developer Unit - Page 7 Questions & Answers
Cant connect to my computer.
Click on start button, and then click on printers and faxes. If you do not see your printer listed, click on add printer, and follow the instructions to add your printer
Make it the default printer, and then it will come up for all print jobs
Lanier MPC 3000 copier won't print faxes
Try opening up your web browser and type in the ip address of your lanier.
You should to access the facsimile function located on the left side. Once youre in the facsimile function, you should see a thumbnail view of the faxes stored in your lanier. Simply click on the faxes and delete them.
Wrench (repair)light is on. It's a Lanier 7313.
Set the maintenance counter:perform test command 72.Press C - interrupt key - 0 - interrupt key - 7 - 2 - PSW.The currently set maintenance cycle code is displayed and the ready lamp lights up.After the ready lamp lights up anter the set code corresponding to the maintenance cycle mode.0 = 10000 sheets ; 1= 15000 sheets ;2=30000 sheets.See the toner full detection part and remove the wastw box,change it.Perfor the test command 14.This command used to cancel troubles other then U1 and U2.After cancellation of trouble the test command is also cancelled automatically,also used to cancel toner full detection the maintenance lamp blinking.
My Lanier 6613 will not pick up the paper to make
Pull out the paper tray from the left side of machine. Insure paper stack is not above the full line located on the back stop, and the back stop in in proper position (labeled on cassette base near the center slots) Also, insure the paper stack is underneath the metal separation claws.
The indication that there are 2 symetrically arranged smudges tells us that the feed pollers are in fact trying to feed the paper, but are not gripping well enough to feed it. On the right side of the copier, at the bottom, is a spring loaded jam removal cover that pivots downward. Open this cover to reach in and clean off the feed rollers. Cotton ball with rubbing alcohol normally does the trick. Just make sure the rollers are dry before trying to feed again. You can also feed single sheets through the bypass feeder. Let me know your progress....Tim
Lanier Model #7320 Copier SN 826255. Has a wrench
Press "clear/stop" and "8" at the same time. An error code will be displayed in the copy quantity window as long as those two button are held down. What is the error code? Each code is specific to different areas of the copier. I will be more than happy to assist you in resolving.
Function Problem with copier
542 errors could be an accumulation of toner on a thermistor for the fusing lamps or a thermostat going out or the connector block or power supply board failling.
Functional Problem SC322
Polygon mirror motor is bad. Sometimes you can put a drop of oil on the shaft, but at best is a temporary fix. You'll end up having to replace it. Good luck
We have a code SC552 functional problem with
if the machine is a plack and white ricoh then the new error code is for the thermistors in the fuser they are not sending the correct temp readings check the fuser for toner build up on the surfaces of the thermistors and check the thermo fuses to see if they are blown....GOOD LUCK aa>>
Getting a red
Press "clear/stop" and "8" at the same time. An error code will be displayed as long as these two buttons are held down. What is the error code? Let me know, please.
How do you reset a lanier 6112 copier so the
The maintenance time is flashing.To be use the service enter code C-0-0-C or C -Interrupt-0-Interrupt,then press 20(maintenance counter clear) and 72 maintenance preset counter setting for a new value.
How do scan a item and send it to my computer
you need to have the scan option. the nic option . print option. you need the the machine being able to print. after that create a folder that is shared on the pc. get the name of the pc. on the machine browse the network, find the pc and search for the folder. this is the shortend version. now you can scan to the pc
Lanier SC 363
check the td sensor it has a high reading.. if this is a colour machine check the yellow dev unit.. some times the gears jam and can cause errors it may need replacing
I have a ricoh mpc 3500, it works fine but i am
Hello sir; There are two way to get rip off the lines,# 1 , aat the end of the transfer belt there have a cleaning unit , clean up , if need to replace cleaning blade , change it. #2 , after you copy , pull out each drum unit check it out see which drum with the line on it, replace that drum unit.
Not finding what you are looking for?