Hotpoint RGB745 Gas Kitchen Range - Answered Questions & Fixed issues

you can turn the supply valve down

it very well is the door switch might be stuck. The way to unstick it is to slam the door. Very often it'll jar the switch loose if that doesn't work you'll need to order one. Easy to install there are youtube videos on it. If you need the part...try here...repairclinic.com or appliancepartspro.com. Hope this info helps a little.

If you are sure you have the correct clock for your model have followed instructions completely, tape up loose wire ends individually and give it a try.

Hello Michael Smith, You MODEL number only came through as a PARTIAL ... (so I filled in the rest (assuming USA)): RGB745 ... wea2ww Please note: Accordingly... you will have to VERIFY the part. Part and video guidance are available here: Third item on the page "heat sensor" http://www.appliancepartspros.com/parts-for-ge-rgb745wea2ww.html Hope this helps... Carnac the Magnificent

Hello. The range you have has a spark ignitor module inside the top, beneath the cooktop. Also, there is a spark ignition harness that has the four switches(snapped onto each of the burner valves at the control panel) connected together(daisy chained) that goes to the module and the incoming 120v supply. HOWEVER, the bigger issue here is getting to the module, harness, and other parts beneath the cooktop. Gas ranges are notorious for having the mount screws seize in the burners. When removing them is attempted, the heads usually snap off causing burner replacement to be necessary(which is why I listed the part numbers for the burners and screws). The cost of this can be high. I suggest calling for service if you are at all hesitant about working on the range. BURNER SCREWS(8) WB1K84 BURNER HEAD RR WB16K12 BURNER HEAD LF WB16K11 BURNER HEAD RF WB16K10012 SPARK MODULE WB13K25 HIGH VOLTAGE HARNESS WB18K06

Make sure igniter is getting power before you replace it. Also check the switch that feeds the igniter. For parts go to attached. Search Over 2 1 Million Appliance Parts

You may find that your new oven cooks differently than the one it replaced. Use your new oven for a few weeks to become more familiar with it. If you still think your new oven is too hot or too cold, you can adjust the thermostat yourself. Do not use thermometers, such as those found in grocery stores, to check the temperature setting of your oven. These thermometers may vary 20-40 degrees. NOTE: This adjustment will not affect the broiling or the self-cleaning temperatures. The adjustment will be retained in memory after a power failure. Adjust the oven thermostat-Do it yourself! To Adjust the Thermostat Touch the BAKEand BROIL HI/LOpads at the same time for 2 seconds until the display shows SF. Touch the BAKEpad. A two digit number shows in the display. The oven temperature can be adjusted up to (+) 35°F hotter or (-) 35°F cooler. Touch the + pad to increase the temperature in 1 degree increments. Touch the - pad to decrease the temperature in 1 degree increments. When you have made the adjustment, touch the START/ON pad to go back to the time of day display. Use your oven as you would normally. NOTE: This adjustment will not affect the broiling or self-cleaning temperatures. It will be retained in memory after a power failure

"bad line" error means the control panel is not seeing a proper voltage to the oven. Have the power connections checked with a voltmeter all the way to the control panel. If voltage is present, you may need a new control.

Your range uses electronic ignition, not pilot lights. For surface burners the igniter sparks when the gas valve is turned to the "light" position. All burners should spark when any gas valve is in the light position. For the oven the ignitor is also electric but does not spark but rather heats up or glows. What is the problem with your range?

Hot point has 2 pilot lights on top... light them... then go to oven and light that one... it is a safety feature... no pilot on top kills the pilot in the stove.
.. since gas is heavier then air the company made sure if there was a gas leak on top that it would not be caught by oven and blow up.

Go to the manufacture site search for manuals on their site for the oven you have... usually PDF format

For the last 10 years or more there are no pilot lights on gas ranges. Modern ranges have an electronic igniter on the burners and a different type on the oven.

All of you are MORONS. the guy is asking "quite clearly", how to remove the bottom pan so he can clean under it. It's quite obviouse he understands how to clean the the main part of the oven. He just want to know HOW TO REMOVE THE BOTTOM PAN.......

Replace the door seals, they are the thin rubber strips around the front of the oven when the door is open. They are simple to change as they just clip on.

Could be a faulty solenoid coil on the gas valve, or a relay you may need to remove the front panel and have a listen be careful it's live power . Use a multimeter to test through the circuits an disconnect the item that's buzzing, there is your problem. Good luck and be careful Ray

sounds like your cooking timer is buzzing

What is the complete model number of your unit?

You don't say if it's natural gas or LP gas, sometimes lp gas will smell if there is low pressure in the cylinder( nearly empty)

http://www.fixya.com/support/p39911-hotpoint_rgb745_gas_kitchen_range/manual-18109 Please read before operating.

F2 During BAKE, Control senses oven temperature above 615F-630F f actual over temperature condition occurred: Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC). Here is the part to order.