20 Most Recent
Lanier LF310 - Page 11 Questions & Answers
We have a dark vertical
It appened when you take a copy????? If so, you probably hava scanner mirror durty.
Lift up de feeder end you see five screws.
Unscrew them and you have access to the mirrors.
Just wipe gently to avoid moving the mirrors
We have a lanier 5216
Hi,
System Setting Reset
The system settings in the UP mode can be reset to theirdefaults. Use the following procedure.
1. Press User Tools/Counter .
2. Hold down the '#' key and then press System Settings.
3. Press yes when the message prompts you to confirm thatyou want to reset the system settings.
4.Press exit when the message tells you that the settings have been reset.Please do rate the solution if the issue is resolved or post a comment for further assistance.
Thank you for using fixya have a nice day:-)
We have a Lanier 5618
first you have to see if it happens when they get to a copy or a print. If it happens in print there is not much to clean, you have to replace worn parts. If it happens only on the copy you have mirrors Sanner dirty. (strip the screws and lifting the glass carefully cleaned the mirrors).
Hope this has helped
Double sided copying does not
look my friend try to open side door and move that two rullers hanging in exit unit try to move more than 5 on's it's works
LANIER 5637 FAULT CODE SC542 UPON POWER UP
You have a Fuser Temperature warm-up error, Hot roller warm-up error.
Verify the heater lamps, thermistor and thermofuse continuity.
Enter in the SP mode, turn OFF the main switch, unplug the machine, wait 10 seconds,
plug in and turn ON the copier.
If you need to reset the fuser, Enter SP 5-810 (SC code reset) and
select "1". Then simultaneously press the Original Type key and the OK (or
R/#) key. (There is no need to turn the main switch off and on.).
Lanier model 5627 with fault code sc542 upon power
LOL I think I already gave you a solution
try this:
1. Press the clear mode key (yellow key)
2. Use the keypad to enter "107"
3. Old down clear/stop for at least 3 secunds. (red key)
4. Enter the service mode.
5. Exit all the way and turn off.
6. Turn ON
And thats it
When we try to copy
Hi shiana,
On the right side of your copier is a "box" called the duplex unit.It really is a silly *** box LOL.Now....either it is not firmly latched to the copier .......OR....the metal tab on the main copier is bent so that even if you put the duplex unit firmly in place ........the little switch on the duplex unit is still not :satisfied: And we hate that. I bet ya got it fixed in a jif. take care :-)
Will only copy documents landscape no matter how
if you are yousing the ARDF keep the document in ARDF ensure that the mater on the document is up side or you are yousing the platen glass keep the document down side on the glass thatsit - thankyou
Lanier 5518 gives a SC320
This SC-320 code error occurs when polygon mirror motor fails or poor connection between BICU & polygon mirror motor please check first the connector of motor if you feel that the connector is good change the polygon mirroe motor it sits inside the LD unit please call the expert to change the part
thanks
Lanier 6613 copier. Image is offset down the page
try making a copy and then open the door when the paper is in the center of the machine. if the image is offset before the paper hits the fuser(hot) rollers>the problem is in your drum unit (most likely a cleaning blade. If it happens after going through the fuser(hot) rollers you have a fuser roller problem. Most likely you have a worn drum cleaning blade which is cheaper the a drum. Good Luck.
I have a lanier 7328/7320.
How are you? This is a problem with front door switch.
Remedy
- Place the machine on a level table and make sure all the four stands are landing freely on this table.
- Check that the front door notch that closes the door switch is not broken and if it is replace that particular door or modify the notch.
- Make sure the upper half of copier is well locked with the lower bottom part.
If all the above is correct, and still reads open, replace the door switch.
Good luck.
Copying a 40 page documente
Well sometimes you can restart the printer...also you can start printing where it left off if you see what page it was and then hit print and look in window and set start page such as 21-40
We just got a Lanier
We also just had someone donate this same type of copier to us and do have a manual. We are currently having trouble with the stapling unit running continuously. The manual is about 130 pages. I may be able to scan it to you in a few days if you'd like.
Not finding what you are looking for?