Yukon 2003 03 Bose/onstar Radio Replacement Adapter - Answered Questions & Fixed issues


Hi Vale Savege, so you may have problems with the connection or the antenna cable
To receive AM, you need to have the connection and antenna cable correctly, while to receive FM, with a shorter cable you can do the same
I sent you the link to download the Service Manual
I hope you can solve the problem
Greetings Franco Dosil

Hola Vale Savege , por lo que comentas puedes tener problema con la conexion o el cable de la antena
Para recibir AM, necesitas tener la conexion y el cable de antena correctamente, mientras que para recibir FM, con un cable mas corto lo puedes hacer igual
Te envio el link para que descargues el Manual de Servicio
Espero puedas resolver el problema
Saludos Franco Dosil
https://usermanual.wiki/Document/XCP410M.742298536/view

Car Audio &... | Answered Yesterday | 25 views


You need to calibrate put a DVD in on the remote press stop,zoom, up, down screen should pop up touch the cross touch the cross at each corner u will see ok turn off and back on and try it

Car Audio &... | Answered 2 days ago | 3,850 views


clocks are in two type one is digital and another is analog it is not specified by you...... sum have a presets inside on board i m not sure it have in your clock show me a picture.

Car Audio &... | Answered 3 days ago | 21 views


locate at service center in market....

Car Audio &... | Answered 3 days ago | 19 views


I believe the white striped wire would be positive (red clamp), BUT DON'T COUNT ON THAT OR GUESS AT IT. Find someone with a volt meter to test the leads and tell you which is positive (red clamp) and which is negative (black clamp).

Car Audio &... | Answered 3 days ago | 14 views


We're can I buy a sd card for my eonon d5156 stereo
5_20_2019_10_17_02_am.jpg

Car Audio &... | Answered on May 20, 2019 | 143 views


This more than likely means that you have a blown fuse. Go to an electronic store and replace the fuses. Make sure you get the exact same sizes and types that you had before.

Car Audio &... | Answered on May 18, 2019 | 273 views


Figure out if its a blown coil or damaged cone

1. Blown Coil:

The voice coil is the component, which amplifies the current run through the speakers. If you doubt that the coil is damaged, connect the terminals of the coil to a multimeter, and if there is no resistance detected, it could be because the coil is damaged.

2. Damaged Speaker Cone:

If there are no issues with the coil, the next possibility can be a damaged speaker cone, which can be detected easily. In normal condition, since the subwoofer is built on a suspension system, the cone is easy to move. Look for the following signs to understand that your speaker cone is damaged:
  • If you could gently take the cover of the subwoofer off and check for the movement of the cone by gently pushing along the sides
  • If the cone is rigid and does not move its indicator
Once you make sure that you have a blown subwoofer, the next step will be deciding on how to replace it. Imagine if your subwoofers can be fixed easily with minimal efforts within a set budget rather than buying a new one.



Then

1. Detaching the speakers:

Use a screwdriver to take the speakers from the place where it is mounted and take off the attached wires. After that, separate the surround and the frame by removing the glue on the frame edge by using a small knife or a sharp object like a tester edge. Be very careful when you do this because the frame edges can be damaged.

2. Separate the voice coil and speaker cone:

Using the same small knife or a tester edge, slowly take out the voice coil from the speaker cone. Cut all the terminal wires and keep the voice coil, speaker cone, and spider separately in place.

3. Fixing the new voice coil:

Clean the trapped dust particles in the voice coil gap carefully by using the compressed air. The voice coil is the piece of wire that is attached to the speaker cone, and that is responsible for amplifying the current, which is passed through the speakers. Remove the old voice coil and fix the new voice coil within the space if the problem is with the coil. Place the spider around the new voice coil, replace the spider and then the speaker cone in the middle. Don't forget to apply enough glue so that the cone doesn't come out. Let it dry for about 24 hours.

4. Fixing the speaker frame:

After it is dry, apply glue on the surround to fix the speaker frame and the cone in the right position. Now we are about to reassemble the components of the sub-woofer.

5. Fixing the wires:

Once all the components are put together in the right place, use a soldering iron to connect the old terminal wires with the new voice coil terminal wires, if the voice coil is replaced. If the new cone has no pre-attached wires, use small wires to the terminal wires, and then create small holes in the cone. Place the wires into the holes and connect them to the voice coil using the soldering iron.Now the connection is also reestablished.



voice coil-1euwbik0fczxdvih31i5iaxf-4-0.jpg

Car Audio &... | Answered on May 18, 2019 | 26 views


Hi Ed, check if the Vol + is not stuck on the remote control
Check it and comment
Greetings Franco Dosil
Hola Ed, controla si no se quedo trabado el Vol+ en el control remoto
Revisalo y comenta
Saludos Franco Dosil

http://manual.kenwood.com/files/IM382_Ref_K_En_02.pdf

http://manual.kenwood.com/files/IM382_Ref_K_Es_02.pdf

Car Audio &... | Answered on May 13, 2019 | 20 views


Long time since the question was asked, but if someone googles it.
I have a Vauxhall Vectra -04 with a cdr 2005 radio/cd player.
Suddenly when I started the engine the radio showed ”panel” I turned radio of and then pressed AS and turned radio on while pressing AS, now it said ”10 safe” but I couldn’t enter the code. So I disconnected the battery and then reconnected it again, then turned ignition on, the radio said ”10 safe - - - -” and I was able to enter my code, then pressed AS and heard a beep, now it’s working just fine again

Car Audio &... | Answered on May 13, 2019 | 255 views


Google (brand)(rz307)(manual) without parens.

Car Audio &... | Answered on May 13, 2019 | 20 views


check a stereo supplier you need a module harness if u change the radio if you get a harness with red wire seperate ,that wire is connect to a ignition source so radio will work ..but keep in mid the door chime will not work any more

Car Audio &... | Answered on May 13, 2019 | 23 views


Hello Brian, I do not know what amplifier for the car you have, but generally, the negative of your amplifier goes to negative battery and positive to positive battery, with the cable section indicated by the manufacturer of the amplifier
Then you will send the audio output from the stereo to the amplifier input through shielded cable
Discuss what amplifier and what stereo you have, indicate brand and model, to improve the response I am giving you
I await your comment
Greetings Franco Dosil

Hola Brian, no se que amplificador para el auto tienes, pero por lo general, el negativo de tu amplificador va a negativo de bater?a y el positivo a positivo de bater?a, con la secci?n de cables que indique el fabricante del amplificador
Luego mandaras la salida de audio desde el est?reo a la entrada del amplificador a trav?s de cable blindados
Comenta que amplificador y que est?reo tienes, indica marca y modelo, para mejorar la respuesta que te estoy dando
Espero tu comentario
Saludos Franco Dosil

Car Audio &... | Answered on May 12, 2019 | 22 views

Not finding what you are looking for?
Yukon 2003 03 Bose/onstar Radio Replacement Adapter Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Yukon Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5013 Answers

Marvin
Marvin

Level 3 Expert

84625 Answers

The Knight
The Knight

Level 3 Expert

76046 Answers

Are you a Yukon Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...