20 Most Recent Clarion DB245 CD Player - Page 4 Questions & Answers

Here you go.

http://www.clarion.com/us/en/MungoBlobs/147/315/DB455MC(Install).pdf

Good Luck and Please Rate FixYa!

This is from the 225 but should be the same:

Setting the Clock
1) Press and hold the BND button 0, and then
press the DISP button 9 to display the clock
display.
2) Press and hold the BND button 0, and then
press the DISP button 9 for 2 seconds or
longer.
3) Press the SRCH Up button ´, then set the
current hour.
4) Press the SRCH Down button ´, then set
the current minute.
5) Press the BND button 0, then the clock is
set.
Notes:
• If you select another operation mode while you are
setting the clock, the clock setting operation will be
canceled.
• If you remove the vehicle’s battery for a check or
repair, the clock will be reset, so you must set it again

Press and hold BAND then press DISP (#4)
here's the manual:
http://www.clarion.com/us/en/MungoBlobs/468/198/DB245(Manual).pdf

hi, yes, problem is solved thanks to fixya. i used the solution that you posted to set the clock and it fixed my problem too.
thank you
joey

THE MOTOR RESPONSIBLE FOR EJECTING THE CD MAY HAVE FAILED U CAN OPEN THE TOP OF THE UNIT AND TRY TO RELEASE THE CD, BUT BE CAREFUL THEY R DELICATE PARTS

HOOK THE UNIT DIRECTLY UP TO THE BATTERY IF THE SAME CONDITION EXIST THE UNIT IS BAD.

THAT TYPE OF CONFIGURATION MUST BE OBTAINED FROM THE USER MANUALS

GO TO AN AREA THAT HAS STRONG SIGNAL AND HAVE THEM REPING THE RADIO.IF THAT DOES WORK REQUEST A NEW UNIT, ALSO CHECK YOUR ANTENNA TO MAKE SURE IT HAS NOT BECOME DAMAGED

it can be ordered from www.pacparts.com

Part number 854365900 for $15.89

Don't worry about the brown wires. They are for telephone mute.

The yellow is Memory (constant 12 volt, so battery is fine), but the red should go to a 12 volt source that turns on and off with the key.

kenwood dpx-4020

The yellow wire from the ignition key goes with red wire from battery.

I think you press and hold the band button then press the display button

ok on top u skip the first big hole and the 2nd hole then it should go orange blue space red spacegreen and black. then bottom yellow then purple then purple then grey and black thengrey then white then white black then green

go to pacparts.com

You need to connect the YELLOW wire to +12VDC also.
The YELLOW wire is for the memory of the radio and it connected to constant power line.

Mute Button https://www.google.com/search?q=clarion+nx501+mute+button&

NX501E NZ501E

Clarion Global https://www.clarion.com > MungoBlobs > NX501... PDF • Press this button more than 1 second to stop video and audio media. [MUTE] Button. • Mute or Unmute the speaker. • The symbol on upper right area of the ... 123 pages

Switching On, Off Or Mute; Audio Source Selection; ...

ManualsLib https://www.manualslib.com > ... > User manual Press the button again to cancel the mute function. ... by turning off the vehicle ignition and removing the vehicle ignition key. Audio source selection. AM/FM.

NX501A

Clarion Global https://www.clarion.com > NX501A_ENG PDF • Press this button more than 1 second to stop video and audio media. [MUTE] Button. • Mute or Unmute the speaker. • The symbol on upper right area of the ... 138 pages

Functions Of Remote Control Buttons - Clarion Manuals

ManualsLib https://www.manualslib.com > manual > Clarion-Nx501 Functions Of Remote Control Buttons - Clarion NX501 Owner's Manual & Installation Manual ... and audio media. [MUTE] Button. • Mute or Unmute the speaker. • The . ..

Press and hold the [BND] button, and then press the [ ] to select the "TEL MUTE" or "TEL OFF".

If the radio is a factory radio, the code to unlock it should be on a business card size piece of paper with the owners manual and warranty booklet. The card will say radio code and have a six digit number.