Motorcycles Logo

Related Topics:

B
Bill walsh Posted on Jan 22, 2016

Wont start unless you push the slider down in the carb

5 Related Answers

Anonymous

  • 7 Answers
  • Posted on Oct 14, 2009

SOURCE: gas in tank wont start unless put gas in carb-then

Hi, being a tiller theres a good possiblity that the line is glogged and if theres a line filter it could be plugged also. Another source of clogging is from old gas, ti can become a little varnished.

Remove the line clear it with compressed air or other source, drain the tank and if theres a line filter - replace it.

Another source could be the air filter - usually a sponge. Replace this as well or clean in a varsol bath. squeeze it out dry, then apply some oil to the input side - helps to catch dirt, etc.

USE safety precautions .

dont forget to vote

Ad

Anonymous

  • 2309 Answers
  • Posted on Nov 16, 2009

SOURCE: 1979 ford f250 wont start unless i put gas in CARB

first of all you have no carb its fuel injected, at least you know you have spark, now do you have fuel pressure??, is the fuel pump working?/ if you have fuel and pressure then you have to check signal at the injectors, so if you have fuel pressure and a good injector pulse the next step is to check the injectors, this may require removal, good luck

rwvanlue

Roland W VanLue

  • 486 Answers
  • Posted on Nov 24, 2009

SOURCE: TORO CCR 2000 WONT START UNLESS YOU SELF PRIME

Fuel starvation - 'lean fuel' condition
Basic things to check:
1) spark plug
2) spark arrestor in muffler
3) fuel lines and tank filter
4) turn adjustment needles out (counterclockwise) 1/4 to 1/2 turn
Chain Saws:
5) check impulse tube and intake boot for cracks or leaks
*if all of the above are OK and/or do not improve performance then:
Remove Carburetor
6) replace gaskets/diaphragms
a) use a spray carb cleaner to clean jets, holes, and body of carb
b) fuel pump diaphragm goes against the carb body,
then the gasket towards the outside
c) metering gasket goes against the carb body,
and the diaphragm goes towards the outside

I’m happy to assist further over the phone at https://www.6ya.com/expert/rolandw_c013176d62ee17ae

Anonymous

  • 2309 Answers
  • Posted on Dec 01, 2010

SOURCE: 1987 nissan 1987 d21 hardbody

first thing to check is for fuel supply to the carb, it may be just a filter, worse off is you may have to rebuild the carb

alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on Nov 12, 2012

SOURCE: truck wont start unless i put gas in carb and once it starts it wont stay running unless foot is on pedle

is this a carb model or a injection and what year and model would be of a help

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

On a Toyota fork lift with a impco model j propane carb it won't start unless you push the slider down with your finger

I have no experience with propane stuff but from your description I suspect the cold start enrichment is not working or at least it isn't getting enough gas.

This would tend to be proved if the engine fires up on a whiff of ether.
0helpful
1answer

Wont start if you push the slider in the carb it will start

bill, is the slider, a choke? if so it wont run until you choke it usually means there is some kind of blockage in the carburetor. you may have to clean the bowl and little bolt with holes in it or possibly take off the carburetor and clean it. while it is off go ahead and put a rebuild kit in it. most kits are from $5.00 to $10.00. this should correct your problem. good luck
Jan 22, 2016 • Garden
0helpful
1answer

My 86 honda 250 sx wont start. It will start if i use starting fluid for a second but thats it. Before it would shut down after rideing it for a few,so i took the carb off,cleaned it put it back on and it...

I would say that the incorrect of use of gasket goo instead of the proper gasket has spilled into the bowl after assembly and is blocking the main jet --again
when working on a carby , there is no successful "short cut or lazy action"
Mar 07, 2017 • ATVs
1helpful
1answer

Gl1000 carbs rebuilt, at start up, revs to 3k, wont throttle down, help!!

happened on mine, turned out one of the carb pistons/liders was put back wrong, (it was late and dark), the piston/slider in the carb was stuck half open
0helpful
1answer

Truck wont start unless i put gas in carb and once it starts it wont stay running unless foot is on pedle

is this a carb model or a injection and what year and model would be of a help
0helpful
1answer

My pit bike wont stay runnin

sounds like your carb could be blocked with dirt if it wont start unless you put juice down plug i would take the carb off and give it a good clean and also make sure the jets ok just clean them with carb cleaner and a paper clip
0helpful
1answer

My 01 yz 125 wont start with kick start,n loses power in low rpms

sounds if you picked up some water/dirt in fuel when was low

clean fuel bowl and flush carb by drain port if still ruff then remove carb for cleaning
Not finding what you are looking for?

115 views

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Brad Brown

Level 3 Expert

19187 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66971 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...