Service engine light is on. code states spark plug #1 misfiring

Was the spark plug oil fouled or fuel fouled?

https://www.700r4transmissionhq.com/p0301-Dodge-Dart/

Diagnosing Mercedes Benz Misfire DTCs Auto Service World
Thanks

IT could be something such as a loose plug wire.The best advise I can give you is to take your jeep to your local auto parts store and have them pull the codes out of your on board computer.This will give you an area that you can concentrate on to make the necessary repairs to get your check engine light to go out.

mass air and tps would be 2 most common causes.

P0301 - Cylinder 1 Misfire Detected.

Causes:
- Improper spark plug at cylinder #1
- Insufficient compression at cylinder #1
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #1
- Fuel injector #1 may be faulty
- Intake air leak

Solutions:
- Perform Injector Service
- Replaced Spark Plug #1
- Replaced Injector #1
- Replaced Ignition Coil #1

P0303 - Cylinder 3 Misfire Detected.
Follow info from P0301.

P0316 - Misfire Occurred In The First 1,000 Engine Revolutions.

Causes:
- Damaged CKP sensor.
- Ignition System.
- Fuel Injectors
- Running out of fuel
- Fuel Quality
- Base engine
- Damaged Powertrain Control Module

Solutions:
Usually the P0316 is combine with a P03XX codes. The P03XX code indicates in which cylinder the misfire occurred.

apply brake and accelerate engine while vehicle is standing still, you need to apply brake hard, DO NOT do this for a period of more than 1 minute or you will be putting alot of stress on your transmission. you will be trying to set off the "check engine" warning lamp or the "service engine soon" warning lamp, and get a misfire failure code, after code sets on your vehicle computer, get it scanned it will tell you which engine cylinder is misfiring ie "P0301= cylinder #1 misfire" then check out spark plug, spark plug wire and ignition coil. one of them is probably causing this.

Code P0303 means that there is a misfire detected on cylinder #3. This could becaused by anything from a worn out spark plug to a blown cylinder head gasket, a faulty fuel injector, a bad ignition coil, or a leaking intake manifold gasket. I have also seen this type of code caused by clogged-up EGR ports in the intake manifold on certain engines. "Freeze Frame Data" stored in your Engine computer along with the fault code is designed to help identify what engine conditions (high speed/slow speed, heavy load/light load, etc.) are producing the misfire. This helps a lot in identifying exactly what is causing the cylinder to misfire.

One way to eliminate some of the possible causes is to swap parts with another cylinder to see if the code changes.

If you have "Coil-On-Plug" ignition, you can swap the coil on #3 cylinder with the coil on #4 Cylinder and swap the #3 spark plug with the #2 spark plug. Then clear the codes and drive the car till the Check Engine (or Service Engine Soon) light comes back on.

If it still gives you P0303, then it is not being caused by the plug or the coil. It could be any of the other possible causes listed above.
If it now gives you P304, replace the bad ignition coil that is now on #4 cylinder.
If it now gives you P302, Then replacement of all the spark plugs is recommended.

Are you sure it's the spark plug that's faulty or the ignition wire?? How old are plugs and wires?
If you don't know if it's your spark plug not firing or your ignition wire you could move spark plug to number 1 then check your code reader.
Or you could do an ohms continuity test on your number 2 ignition wire to verify that there is no break in the wire. Common problem to check for. If wires and plugs are old and high mileage maybe should change all including cap and rotor on distributor. Fresh wires plugs cap and rotor always improve mileage and performance.
Good luck, sorry can't help with tranny.

Code P0301
Ignition Coil Pack
Ignition Cable
Spark plug
Clog or dirty fuel injector
Evap canister purge valve
Engine Compression
fuel pressure

you have 3 type of engine for your truck
2.3L 4 cylinder
3.0L 6 Cylinder
4.0L 6 Cylinder

need to know that type Engine

The reason why the service light come on because it is a hard code
not a soft code.

Let me know

Hello I need a help.
I have 1999 lincoln town car 4.6L V8.They have check engine light on. P 0303 cylinder 3 missfire.
I was changed spark plugs,fuel filter. check compression test 150psi. fuel pressuer 50.
swiching cylinder 1 to 3 fuel injector and coil. but they still have engine code