Front end parts upper and lower ball joints tie rods and wheel bearrrings how long take to fix and reasonable cost

if this has a conventional front end(not front wheel drive) then there will be one on each outer tie rod end one on each inner tie rod end, both upper and lower ball joints on each side, idler arm and pitman arm. if its front wheel drive it will have a rack and pinion steering. there for there will be one on each outer tie rod end and one on each lower ball joint, if they have grease fittings. so conventional steering has 10 fittings total and rack and pinion has 4 total.

Check for bad wheel balance, struts, lower ball joints ( no upper joints) , outer tie rod ends, inner tie rod ends, stabilizer bar bushings, lower control arm bushings , and finally a wheel alignment ,you have some bad looseness in one or more of these front end parts. GOOD LUCK FRIEND.

Upper ball joint? That's not related to the job of replacing a tie rod or tie rod end. It's also not related to the brake job.

It's an '07 and it had a bolt-in ball joint? That's not factory - it's been replaced before.

Replace the ball joints and/or rod ends.

Very little info for a fix. Tie rod and upper ball joints do not make a front end shake. Lower ball joints wear out before the uppers do.
Front end shakes at what speed, if you have a broken belt in one of your front tires you will notice it more at low speeds. Mud or snow stuck in wheel will make them vibrate at speed. Lug nuts tight since front end work? You need to give more info. Switch front tires with back tires. If shake is in steering wheel it more than likely is front end but if you feel it in your seat it is more than likely in the rear of the car.

You can't stop short with front end repair or your just throughing money away . But upper and lower ball joints are the biggest problem on this vehicle . The uppers are not bolted they used rivits to hold them to the frame and with antilock brakes the vehicle shakes from side to side and this loosens the rivets once there loose the front end can not be alinged So start with that ball joints the rest of the parts are heavy dudty

May be dry ball joint or tie rod end.

Removal & Installation NOTE This procedure requires the use of the following special tools: J 9519-E Lower Ball Joint Remover and Installer, J 34874 Booster Seal Remover/Installer, J 41435 Ball Joint Installer, J 45105-1 Ball Joint Flaring Adapter and J 45105-2 Receiver.

1. On 4WD vehicles, remove the wheel center cap and drive axle nut.
   
2. Raise and support the vehicle.
   
3. Remove or disconnect the following:
   
   • Tire and wheel
     
   • Wheel hub and bearing, if necessary
     
   • Outer tie rod retaining nut
     
   • Out tie rod from the steering knuckle using a suitable puller
     
   • Brake hose bracket retaining bolts and bracket
     
   • Upper control arm-to-steering knuckle pinch bolt and nut
     
   • Upper control arm from the steering knuckle
     
   • Lower ball joint retaining nut
     
   • Steering knuckle from the lower control arm using a suitable ball joint removal tool
     
   • Steering knuckle from the vehicle
     
   • Lower ball joint flange with a chisel
     
4. Install tools J 9519-E and J 34874 to the lower ball joint, then use those tools to remove the lower ball joint from the lower control arm.
   

To install:

1. Install or connect the following:
   
   • Lower ball joint to the lower control arm, using tools J 9519-E, J 41435 and J 45105-2
     
2. Remove the tools from the lower control arm.
   
   • Tools J 9519-E and J 45105-1 to the lower ball joint
     
3. Flare the lower ball joint flange with J 9519-E and J 45105-1, then remove the tools from the lower ball joint.
   
   • Steering knuckle to the lower control arm
     
   • Lower ball joint retaining nut and tighten to 81 ft. lbs. (110 Nm)
     
   • Upper control arm to the steering knuckle
     
   • Upper control arm pinch bolt and nut and tighten to 30 ft. lbs. (41 Nm)
     
   • Brake hose bracket to the steering knuckle
     
   • Brake hose bracket retaining nuts and tighten to 7 ft. lbs. (10 Nm)
     
   • Outer tie rod to the steering knuckle
     
   • Outer tie rod retaining nut and tighten to 33 ft. lbs. (45 Nm)
     
   • Wheel hub and bearing, if removed
     
   • Tire and wheel
     
4. Lower the vehicle
   
   • Drive axle nut, if 4WD, and tighten to 103 ft. lbs. (140 Nm)
     
   • Wheel center cap, if removed
     
5. Check the front wheel alignment.
   

The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

What was said about the wear of the front end part when the alignment was given? I could be wrong but, I would say, Not likely for the tie rod ends and definately not the shocks for knocking sounds.. It sounds more like bad ball joints poping, although the idler arm and tye rod ends could be worn also .