Remove and replace spark plugs - 2000 Mazda MPV

Spark Plug Replacement
Tools Required J 38491 Spark Plug Boot Removal Tool

Removal Procedure

1. Turn OFF the ignition switch.
2. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement in Engine Mechanical.


Click to Enlarge

3. Note the position of the spark plug wires before removing the wires.
4. Twist the spark plug boot 1/2 turn before removing the boots.
5. Gently pry the heat shield up from the spark plugs using the J 38491 .
6. Remove the spark plug wires from the spark plugs.
7. Remove the spark plugs from the engine.
8. Hope this helps, as far as spark plugs on backside of of engine, it just depends. Some people rock the engine forward to get at rear plugs. Sometimes I crawl underneath see if easier to reach plugs? There can be safety issues working under a vehicle. Safety is your responsibility. Your local auto store should have whatever tools you need.

Here's a video on changing your rear spark plugs. 2007 Kia Sportage EX rear spark plug replacement

Things you will need
Spark Plug Socket And Wrench of the correct size for your spark plugs


Basic Instructions.
Step 1
Locate your spark plugs
look for other obstructions besides your spark plug wires
if you have any other obstructions you will need to remove them as well to gain access to your spark plugs.
Step 2
Remove the spark plug wire for one single spark plug at a time.
this will insure you will not replace the wrond spark plug wire to the incorrect spark plug,
if not done this way you could change the firing order of your engine.
Step 3
With your spark plug Socket and wrench rotate the spark plug in a counter clock wise direction for removing.
Step 4
After you have removed your spark plug insert your new replacement spark Plug into your spark plug socket before inserting it into the correct location. spark plug sockets are made to hold on to the spark plug for easy removal and install.
Step 5
insert your new spark plug,
before you rotate your spark plug for tightening rotate the spark plug a 1 quarter turn in the counter clock wise direction, then start tightening the spark plug by rotating it in a clockwise direction
This will insure you will not strip the threads.
Step 6
Continue rotation your spark plug in the clock wise direction untill snug, then with just a lil more pressure tighten it up just a little more.
be sure to not put to much force on the spark plug after it has been snug, you just have to apply a little more pressure but not to much that could cause it to break.
Step 7
After tightening the spark plug replace the correct spark plug wire.
then move on to the next spark plug and follow the same instructions.

if you have any other visiable obstructions preventing you access for replacing your spark plugs you will need instructions on how to remove them parts. i have just instructed you on how to remove and reinstall the spark plugs only.

IF YOU HAVE THE EI IGNITION SYSTEM.YOUR SPARK PLUGS IS UNDER EACH INDIVIDUAL COIL.DISCONNECT COIL ELECTRICAL CONNECTOR.THEN REMOVE COIL RETAINING BOLT.THEN REMOVE OFF SPARK PLUG.THEN REPLACE SPARK PLUG.YOU HAVE 8 COILS TO REMOVE BEFORE REPLACING SPARK PLUGS.

Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.

Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the left side spark plug wires from the spark plugs.
3. Remove the left side plug wires from the retaining clips.
4. Rotate the engine for access as follows:
   1. Set the parking brake.
   2. Shift the transaxle into neutral.
   3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
   4. Install the Engine Tilt Strap J-41131.
   5. Pull on the engine in order to rotate the engine forward.
   6. Tighten the strap.
   
   
5. Remove the right side spark plug wires from the spark plugs.
6. Remove the plug wires from the retaining clip.
7. Remove the spark wires from the ignition coils.
8. Remove the plug wire assembly from the engine.
   NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.
   

To install:

1. Install the right side plug wires to the ignition coils and then the spark plugs.
2. Install the spark plug wires to the retaining clip.
3. Rotate the engine back to the original position.
4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
5. Install the spark plug wires to the retaining clips.

3.9L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the intake manifold cover.
3. Remove the left side spark plug wires as follows:
   1. Disconnect the left side spark plug wires from the spark plugs.
   2. Disconnect the left side spark plug wires from the ignition coil.
   3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
   4. Remove the left side spark plug wire assembly.
   
   
4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
   1. Set the parking brake.
   2. Shift the transaxle into neutral.
   3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
   4. Install the Engine Tilt Strap J-41131.
   5. Pull on the engine in order to rotate the engine forward.
   6. Tighten the strap.
   
   
5. After rotating the engine, remove the right side spark plug wires as follows:
   1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.
   
   
6. Remove the right side spark plug wire clip from the ignition coil bracket.
7. Remove the right side spark plug wire assembly.

To install:

1. Install the spark plug wire assembly.
2. Install the right side spark plug wire clip at the ignition coil bracket.
3. Connect the plug wires to the ignition coil and spark plugs.
4. If the engine was rotated for access, return the engine to the original position.
5. The remainder of the installation is the reverse order of removal.

Remove the cowling that the windshield wipers go through.
This piece is removable. On my ford the wiper motor comes off with the cowling.
This is the trick.

On the 3.5L the Electronic Coil Packs are located over the Cylinders/Spark Plugs.
These Coil Packs have seven (7) bolts on a Black Cover. Remove these seven (7) bolts, removing the Cover.
Access to the three (3) Front Spark Plugs is now gained.
The Rear three (3) Spark Plugs is the same, however it is in a tight spot near the Fire Wall.

Standard Rules: Some things are not Applicable for your specific engine.
Use a Spark Plug Socket to remove and install Spark Plugs.
Replace (remove) one Wire Connections at a time from one Spark Plug.
Replace One Spark Plug at a time. Use Anti-Seize Grease applied moderately to the threads on the new Spark Plug.
Using a Socket (with a extension) START all installations of all Sprak Plugs using your hands. This prevents cross-threading and stripping of the threads inside the Heads.
Standard Torque 15-20 ft-lbs.
Replace the One Wire Connection to that One Spark Plug.
Replace that One Wire Connection to the Ignition Coil Connection.
Go onto the next Spark Plug using the above Rules.
Repeat.

For the 3.5L
Firing Order:
1-2-3-4-5-6
Cylinders:
.....(back)
1......3.......5
2......4.......6
....(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Engine off
Remove one spark plug wire / using correct size spark plug wrench with / rubber boot designed for spark plugs (deep well socket with rubber boot) remove (1) spark plug / gap new replacement spark plug to specs / install replacement spark plug by hand into head of engine /finger tight /using spark plug socket and rachet finish tighting spark plug / tighten just beyond snug being careful to not over tighten and breaking spark plug ..if in doubt about the proper tighting consult motor manual for torque specs. use torque specs in conjunction with appropiate torque wrench . Re-install removed spark plug wire ...proceed to remaining spark plugs doing one at a time until completed.

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
   NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
2. Remove the intake manifold cover, if required.
3. Disconnect the left side spark plug wires from the spark plugs.
4. Disconnect the left side spark plug wires from the ignition coil.
5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
6. Remove the spark plug wire assembly.
7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
8. Disconnect the right side spark plug wires from the spark plugs.
9. Disconnect the right side spark plugs from the ignition coils.
10. Remove the spark plug wire assembly.
11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.

To install:

1. Install the spark plug wire assembly.
2. Connect the right side spark plugs to the ignition coils.
3. Connect the right side spark plug wires to the spark plugs.
4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
5. Install the spark plug wire assembly.
6. Connect the left side spark plug wires to the spark plugs.
7. Connect the left side spark plug wires to the ignition coil.
8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system


Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system


I really hope help you with this (remember rated this help) Good luck.

My 2004 Verona had factory installed "NGK BKUR6ETB" regular spark plugs which I replaced at 30,000 miles. The 2005 model year is supposed to have Iridium spark plugs. To replace the spark plugs: 1. Remove plastic top engine cover. 5 nuts 10mm socket. 2. Unplug connector from each ignition coil. qty 6. 3. remove 2 hold down bolts per ignition coil. 10mm socket. 4. remove ignition coil, lifting straight up. 5. Spark plug is now accessible, use deep well 5/8 spark plug socket to remove.