I have the same problem plus my transmission seems to be going

Not to worry friend, when my machine go sick i avoided going to mechanic looking for DIY_Repair when I found this website https://big-manuals.com/ and this book helped me repair it within an hour, all by myself!!!
From wiring diagrams, schematic illustrations, spark plugs info, parts info, chassis number, valve time settings, step wise instructions, torque specs, error/fault codes, engine info, to every single minute parts, you get everything in there you can't imagine how detailed it is

Your problem is more then likely with the Automatic Transmission Shift Lock Control .This is a safety thing . Has a switch , wiring and a electrical solenoid .
Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
• The park/neutral position switch

Sorry to here your having a problem with it already .
There are diagnostic step to find the problem , involves using a DVOM - digital volt ohm meter an using a wiring diagram to locate test points in the circuit . Plus you will need to take parts of your vehicle apart to get to those test points . The most likely part to fail is the park neutral safety switch . The contacts wear inside after hundreds of times of moving the shifter . But without testing this is just a guess .

With the ignition in the ON position, battery positive voltage is supplied to the park/neutral position switch. With the transmission in the PARK position, the contacts in the park/neutral position switch are closed. This allows current to flow through the switch to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid, mechanically locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to move from the PARK position.

Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid

?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
Shift Lever Does Not Move with Brake Pedal Depressed ?

2

1. Turn ON the ignition.
2. Press and hold the brake pedal.
3. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections
Go to Step 3

3

1. Turn OFF the ignition.
2. Disconnect the automatic transmission shift lock control switch.
3. Turn ON the ignition, with the engine OFF.
4. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
Go to Step 7
Go to Step 4

4

1. Turn OFF the ignition.
2. Leave the automatic transmission shift lock control switch disconnected.
3. Connect a test lamp between the A/T shift lock control solenoid supply voltage circuit at the automatic transmission shift lock control solenoid and a good ground.
4. Turn ON the ignition with the engine OFF.

Does the test lamp illuminate?

5

1. Turn OFF the ignition.
2. Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and a good ground.
3. Turn ON the ignition with the engine OFF.

Does the test lamp illuminate?
Go to Step 6
Go to Step 9

6

1. Turn OFF the ignition.
2. Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and the park lock solenoid ground circuit.
3. Turn ON the ignition with the engine OFF.

Does the test lamp illuminate?
Go to Step 8
Go to Step 11

7

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Step 13

8

Inspect for poor connections at the harness connector of the park lock/automatic transmission shift lock control solenoid assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Step 12

9

Repair the open or high resistance in the park lock solenoid ignition 1 voltage circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

10

Repair short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

11

Repair the open or high resistance in the park lock solenoid ground circuit. Refer to Circuit Testing or Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 14
--

12

Important: Depress the button on the side of the shift lock actuator. With the button is depressed, cycle the plastic straw within the shift lever 3 to 5 times. The straw should move smoothly and freely except near the top of the travel where additional force will be required to mechanically actuate the park lock mechanism inside of the shift lock actuator. If there is stick/slip or abnormal friction while cycling the plastic straw or if the straw is altogether stuck in the lever, the entire control assembly (shifter and shift lock actuator) needs to be replaced. Refer to Transmission Control Replacement . If there is no abnormal friction, replace the shift lock actuator. Refer to Automatic Transmission Shift Lock Control Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Problem with shift interlock system .
Automatic Transmission Shift Lock Control Description and Operation
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid

?€¢
The body control module (BCM)

?€¢
The powertrain control module (PCM)

With the ignition in the ON position, battery positive voltage is supplied to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid receives a ground from the BCM. When the automatic transmission shift lock control solenoid is energized, the shift lever mechanically locked in the PARK position. When the driver presses the brake pedal the PCM sends a class 2 serial data message to the BCM. The BCM turns OFF the ground control circuit and this de-energizes the automatic transmission shift lock control solenoid. When the automatic transmission shift lock control solenoid is de-energized, the shift lever may be moved out of the PARK position. The BCM determines transaxle shift lever position through a class 2 serial data message from the PCM. The PCM receives inputs from the park/neutral position switch and determines shift lever position. When the BCM receives this information and determines that the shift lever is out of the PARK position, the automatic transmission shift lock control solenoid ground is opened.

1

Did you perform the A Diagnostic System Check - Automatic Transmission Shift Lock Control?
Go to Step 2
Go to Diagnostic System Check - Automatic Transmission Shift Lock Control

2

1. Turn ON the ignition, with the engine OFF.
2. Press and hold the brake pedal.
3. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3

3

1. Turn OFF the ignition.
2. Disconnect the automatic transmission shift lock control solenoid.
3. Turn ON the ignition, with the engine OFF.
4. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
YES - Go to Step 4
NO - Go to Step 5

4

Test the A/T shift lock control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 9
NO - Go to Step 6

5

Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 7

6

Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 8

7

Replace the automatic transmission shift lock control solenoid. Refer to Transmission Control Replacement in Automatic Transaxle-4T40-E/4T45-E.
Did you complete the replacement?
Go to Step 9
--

8

Replace the body control module (BCM). Refer to Body Control Module Replacement in Body Control System.
Did you complete the replacement?
Go to Step 9
--

9

Operate the system in order to verify the repair.
Did you find and correct the condition?
System OK
Go to Step 2

The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid

?€¢
The body control module (BCM)

?€¢
The powertrain control module (PCM)

The BCM controls the voltage to the shift lock control solenoid through the shift lock control solenoid controlled voltage circuit. The following conditions must be met before the BCM will supply voltage to the shift lock control solenoid:
?€¢
The ignition is in the ON position.

?€¢
The PCM sends a class 2 message to the BCM indicating the transmission is in the PARK position.

?€¢
The BCM determines the brake pedal is not applied according to the stop lamp switch.

When the ignition is in the ON position, the ignition 1 fuse supplies voltage to the automatic transmission shift lock control solenoid as the BCM supplies a ground to the control circuit, mechanically locking the shift lever in the PARK position as the solenoid energizes. When the brake pedal is applied, the BCM turns the ground of the control circuit OFF, de-energizing the shift lock control solenoid. The de-energized solenoid releases the mechanical lock allowing the driver to move the shift lever out of the PARK position. When the transmission is out of the PARK position, the shift lock control solenoid remains de-energized.
Your best bet is to take it to the dealer ,may have DTC'S
DTC B2707 Gearshift Unlock Circuit Low
The body control module (BCM) controls the automatic transmission shift lock control solenoid by providing a controlled ground to the automatic transmission shift lock control solenoid. The BCM utilizes a smart driver to monitor the voltage and current flow of the automatic transmission shift lock control solenoid control circuit. DTC B2707 will set when the BCM detects a short to ground when the solenoid is in the OFF state.
DTC B2708 Gearshift Unlock Circuit High
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

1. Turn ON the ignition, with the engine OFF.
2. Press and hold the brake pedal.
3. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

1. Turn OFF the ignition.
2. Install a scan tool.
3. Turn ON the ignition, with the engine OFF.
4. Press and hold the brake pedal.
5. With a scan tool, command the Brake to Shift Relay output control parameter On.
6. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
Go to Step 4
Go to Step 6

4

1. With the scan tool, observe the Brake Switch parameter in the powertrain control module (PCM) data display list.
2. Press and release the brake pedal several times while observing the scan tool.

Does the brake input display Applied and Released with the brake pedal operation?
Go to Step 5
Go to Diagnostic Starting Point - Lighting Systems in Lighting Systems

5

With the scan tool observe the TR Sw. parameter in the body control module (BCM) data list.
Does the scan tool indicate PARK position?
Go to Step 9
Go to Scan Tool Data List in Engine Controls - 3.4L

6

1. Turn OFF the ignition.
2. Disconnect the harness connector of the automatic transmission shift lock control solenoid.
3. Turn ON the ignition, with the engine OFF.
4. Press and hold the brake pedal.
5. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
Go to Step 7
Go to Step 8

7

Test the controlled ground circuit of the automatic transmission shift lock control solenoid for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 9

8

Inspect for poor connections as the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 10

9

Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 12
Go to Step 11

10

Replace the automatic transmission shift lock control solenoid. Refer to Shift Lock Control Solenoid Replacement .
Did you complete the replacement?
Go to Step 12
--

11

Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?
Go to Step 12
--

12

Operate the system in order to verify the repair.
Did you find and correct the condition?
System OK
Go to Step 3

Your best bet

is it a linkage issue? if the shift lever is working and you can feel the detents, check your fluid make sure it is full and clean, if not you could have internal issues with the trans

Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control is a safety device that prevents an inadvertent shift out of PARK when the ignition is ON. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid.

?€¢
The automatic transmission shift lock control switch.

?€¢
The park/neutral position switch.

With the ignition in the ON position, battery positive voltage is supplied to the park/neutral position switch. When the transmission is in the PARK position the contacts in the park/neutral position switch are closed. This allows current to flow through the switch to the automatic transmission shift lock control switch. The circuit continues through the normally-closed switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid, locking the shift linkage in the PARK position. When the driver presses the brake pedal the contacts in the automatic transmission shift lock control switch open, causing the automatic transmission shift lock control solenoid to release. This allows the shift lever to move from the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid. The system consists of the park lock solenoid. With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.
Shift Lever Does Not Move with Brake Pedal Depressed
DEFINITION: Transmission shift lever will not move out of the PARK position with the ignition ON and the brake pedal pressed.

1

Did you perform the Symptoms - Automatic Transmission Shift Lock Control tests and all the necessary inspection?
Go to Step 2
Go to Symptoms - Automatic Transmission Shift Lock Control

2

1. Turn ON the ignition, with the engine OFF.
2. Press and hold the brake pedal.
3. Attempt to move the shift lever out of the PARK position.

Does the shift lever move out of the PARK position?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO Go to Step 3

3

1. Turn OFF the ignition.
2. Disconnect the automatic transmission shift lock control switch.
3. Turn ON the ignition, with the engine OFF.
4. Press and hold the brake pedal.
5. Attempt to move the transmission shift lever out of the PARK position.

Does the transmission shift lever move out of the PARK position?
Go to Step 6
Go to Step 4

4

1. Turn OFF the ignition.
2. Disconnect the automatic transmission shift lock control solenoid.
3. Turn ON the ignition, with the engine OFF
4. Press and hold the brake pedal.
5. Attempt to move the transmission shift lever out of the PARK position.

Does the transmission shift lever move out of the PARK position?
Go to Step 7
Go to Step 5
Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 9

6

Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
Go to Step 8

7

Repair the short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 10
--

8

Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement in Lighting Systems.
Did you complete the replacement?

Shift interlock problem . do you know what that is ?
Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
Park Lock Solenoid
The park lock solenoid is a safety device that prevents an inadvertent shift out of PARK when the key is in the OFF position. The key must be in the RUN position to release the park lock solenoid.
The system consists of the park lock solenoid.
With the ignition in the ON position, voltage is supplied to the park lock solenoid. The park lock solenoid energizes through a permanent ground unlocking the shift lever. With the ignition in the OFF or ACCY position the park lock solenoid de-energizes and locks the shift lever in the park position.

Shift Lever Does Not Move with Brake Pedal Depressed
Step
Action
Yes
No
Schematic Reference: Shift Lock Control Schematics
Connector End View Reference: Shift Lock Control Connector End Views or Automatic Transmission Related Connector End Views
DEFINITION: Transmission shift lever does not move out of the PARK position with the ignition ON and the brake pedal pressed.
1
Did you perform the symptom table tests and necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Automatic Transmission Shift Lock Control
2
Turn ON the ignition.
Press and hold the brake pedal.
Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Testing for Intermittent Conditions and Poor Connections
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the automatic transmission shift lock control switch.
Turn ON the ignition, with the engine OFF.
Attempt to move the shift lever out of the PARK position.
Does the shift lever move out of the PARK position?
YES - Go to Step 7
NO - Go to Step 4
4
Turn OFF the ignition.
Leave the automatic transmission shift lock control switch disconnected.
Connect a test lamp between the A/T shift lock control solenoid supply voltage circuit at the automatic transmission shift lock control solenoid and a good ground.
Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?
YES - Go to Step 10
NO - Go to Step 5
5
Turn OFF the ignition.
Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and a good ground.
Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 9
6
Turn OFF the ignition.
Connect a test lamp between the ignition 1 voltage circuit of the park lock solenoid and the park lock solenoid ground circuit.
Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?
YES - Go to Step 8
NO - Go to Step 11
7
Inspect for poor connections at the harness connector of the automatic transmission shift lock control switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 14
NO - Go to Step 13
8
Inspect for poor connections at the harness connector of the park lock/automatic transmission shift lock control solenoid assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 14
NO - Go to Step 12
9
Repair the open or high resistance in the park lock solenoid ignition 1 voltage circuit. Refer to Circuit Testing or Wiring Repairs .
Did you complete the repair?
Go to Step 14
--
10
Repair short to battery positive voltage in the A/T shift lock control solenoid supply voltage circuit. Refer to Circuit Testing or Wiring Repairs .
Did you complete the repair?
Go to Step 14
--
11
Repair the open or high resistance in the park lock solenoid ground circuit. Refer to Circuit Testing or Wiring Repairs .
Did you complete the repair?
Go to Step 14
--
12
Important: Depress the button on the side of the shift lock actuator. With the button is depressed, cycle the plastic straw within the shift lever 3 to 5 times. The straw should move smoothly and freely except near the top of the travel where additional force will be required to mechanically actuate the park lock mechanism inside of the shift lock actuator. If there is stick/slip or abnormal friction while cycling the plastic straw or if the straw is altogether stuck in the lever, the entire control assembly (shifter and shift lock actuator) needs to be replaced. Refer to Transmission Control Replacement . If there is no abnormal friction, replace the shift lock actuator. Refer to Automatic Transmission Shift Lock Control Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--
13
Replace the automatic transmission shift lock control switch. Refer to Stop Lamp Switch Replacement .
Did you complete the replacement?
Go to Step 14
--
14
Operate the system in order to verify the repair.
Did you correct the condition?
System OK

Your front wheels might be turned to the right or left "binding" the suspension and actually holding the transmission in park. Try pulling the steering wheel with one hand so it is loose a bit as if you are turning the car while sitting still and then shift out of park. Some cars have a 'shift lock override' button also. This allows you to shift out of park without a key.

Have someone operate the gear shift while you watch the mechanism on the transmission so that you know what parts you are looking for. Shift into the park position, then uncouple the linkage and move the lever on the transmission fully into the park position. Then adjust the length of the linkage while holding the driver's lever in the park position so that the linkage connector goes back together without pulling on anything.