At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I have a 2000 Chevy Tracker. The driver side seat belt is stuck and will not release. I had a new seat belt installed about 6 months ago and it worked for about 1 month and then it did the same thing. The Chevy garage replaced it with a new seat belt for the second time. It worked for about 3 months and now it is stuck again.
Open small plastic access panel located between front and rear doors a
few inches above floor. Disconnect the two wire connector (usually
attached to car frame) and locate the male pin connector, usually 1 red
and 1 blue wires. Run two long wires from a car battery negative post and
positive post (battery on the car or separate.) Hold one wire against one
pin of the connector and quickly touch the other wire against the
remaining pin. This will cause the motor to turn in one direction. If
motor turns in wrong direction simply reverse the wires until motor
brings belt to desired position then quickly remove the wires. Reattach
connectors to resume 'normal' operation after 'CAUSE' has been
repaired.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If the passenger side seat belt in your 2013 Chrysler 200 is stuck around the headrest, it could be due to a variety of issues. Here are a few things you may want to try:
Check the seat belt retractor: The seat belt retractor is responsible for pulling the seat belt back into the housing when it is not in use. If the retractor is faulty or stuck, it could cause the seat belt to become stuck. You may be able to fix the problem by gently pulling on the seat belt to try and free the retractor.
Check for debris: There may be debris or a foreign object stuck in the seat belt mechanism, causing it to become stuck. Carefully inspect the area around the seat belt and try to remove any debris that you find.
Check the seat belt latch: The seat belt latch may be faulty or stuck, causing the seat belt to become stuck. You'll want to check the latch for any visible damage or problems and try to release it.
If you are unable to fix the problem, I recommend having a qualified mechanic diagnose and fix the issue for you. Seat belts are an important safety feature and it's important to ensure that they are functioning properly.
Try this for the back seat: Pull the back seat down. Unscrew all the bolts behind the back seats to release it from the brace. Pull the seat back off the rear deck and out of the car. Feel under the seat cushions for release tabs on both sides. Pull the release tabs to loosen the seat cushion. Push the seat belt buckles into the holes to prevent the seat from getting caught up in the seat cushion
? 1:44 https://www.youtube.com/watch?v=EDh-0rs5Fjo
Oct 26, 2010 - Uploaded by automdvideos
Auto Repair: How to Replace a Power Seat Motor ... 2007 - 2008 Ford Expedition/Lincoln Navigator Driver Bottom Install Video ...2003-2006 Chevy/GMC Seat Cover Install 1 of 3 - eBay Ready ...2000 Ford Explorer Front Seat Track Stuck Motor Repair - Duration: 4:39. by cubmancan 4,959 views. 4:39.
Drivers seat is dead! No power seat or heat. - TheDieselGarage.comwww.thedieselgarage.com/.../96465-drivers-seat-dead-no-power-seat-hea...Mar 22, 2010 - 2003-2005 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2003-2005.... Power seat on driver side didn't work.....passenger did! Neither ...DANG electric seat ' Chevy Truck Forum ' GM Truck Clubwww.gmtruckclub.com/forum/threads/dang-electric-seat.2990/Apr 27, 2006 - 10 posts - 7 authors'03 Tahoe My driver seat just stopped, of corse not where I need it, the ... I have a 2003Tahoe and both heated seats are not working. ... with my seat heater on the drivers seat in my 03 Avalanche, it turns ... The driver's side on my Silverado gets way warmer than the passenger side. ... Frozen New Member.Power Seat Problems?? - Tahoe Forum - Che
You are probably pulling belt at the wrong angle and it won't release. Pull with easy steady tension, trying a different angles and it should come free for you. If it doesn't, then take it back to SEAT or VW, they can show you in 1 minute how to free it. Since it's a mandatory safety device, there should be no charge unless it requires replacement.
of course it possible to access this retractor , you just need to locate the small round circles in the lower part of trim and gently pry the covers off , screws will be evedent , you will need a 6 mm star (five sided) drive socket wrench to remove the retractor though
first for the switch in window
the window switch is easy to test you just gotta remove switch out of the door leaving it hang there is a way to test with a guaged wire with fuse on it
take the main power wire and touch to the other connectors on the main switch if the window goes down or up the switch is the problem
im suggesting this way first with fuse cause its easier then testing the windows motor inside the door frame the switches should just pop out of the panel with out haveing to take panel off
now the seat belts there are 2 style that are common to chevy
one is inside the molding of the drivers panel you gotta pop off the panels easily and gently to get at the seat belt retractor this will be bolted to the metal under the molding
the other style is in the seat which you gotta unbolt the seat under the top half it will need to be unbolted at the bottom top half of seat
when you pull threw the top section of top half of seat remember to tie a string to the end so that when you pull threw top half the string will be there so you can connect too new belt and pull back threw with ease make the string long enough to hang
now the bottom half of seat what i call the "**** seat" you remove the molding at bottom around the belt retractor this will be bolted to floor bolt also pull belt threw molding once molding removed
disconnect any electric wires
now saftey issue involved with seat belt removal is for a reason i dont know of the dealer ship always discharges the belts and air bags once removed i guess because of static electricity becareful when you remove belt and replacing belts cause static elec. can set them off
once your seat belt is removed place in card board box and take to dealer after complition of installing new belt they will discharge your seat belt for you and then you can dispose of it properly
×