Where sensor of air throttle in hyaundai elantra 1.6 engine model 2013

You have changed all the things that have no effect on the root cause of P0172. You need a new Fuel/Air Sensor. Your ECM is showing that the fuel air mixture is too rich, so it is reducing the fuel that is going into the engine. That causes the ECM to compensate by running the engine lean and that causes overheating. Buy a Denso sensor, they are the best.

Hyundai Elantra P0172: Fuel System Rich - Bank 1 - 700R4

https://www.700r4transmissionhq.com > p0172-hyunda...
Nov 21, 2018 - Elantra P0172 Code Defined ... P0172 is thrown when the oxygen sensors detect that the air fuel mixture is too rich. Bank 1 refers to the rich ...


Videos as well

https://www.google.com/search?q=elantra+2008+P0172

..

all cars it is 1 of 3 places off the crank shaft
front ,center or rear,. some even are no the tranny flex plate.(crude reluctor)
the water beetle,
no country told. usa CAR IF YES WHY NOT SAY SO , WE USE JUST ONE 2.0l
NO ENGINE TOLD LOTS OF 2.0.
A5 BEETLE 2012-2013 TSI 2.0L??????

2013 VW beetle 2.0 TSI turbo engine. 16 VALVE?
THE EA888????? 3 generations of TSI MADE, GEN 2 IS 2008
197 bhp 2.0-litre turbo petrol engine
A5 BEETLE
VW OUCH
CALLS IT AND ENGINE SPEED SENSOR. SURE BUT IS NEVER IT'S PRIMARY GOAL EVER (rpm) THE GOAL IS EXACT SPARK AND INJECTION TIMING
NOT SPEED,
USA SHOP MANUAL SAYS.
Engine Speed Sensor G28 <<< BINGO REAL NAME FOUND, HARD TO DO.2.0l

1. On the front lower left side of the cylinder block, next to the oil separator. Refer to (see more...)
2. Removing and installing. Refer to Engine Speed Sensor G28, Removing and Installing.

PULL ENGINE COVER
Open the air guide pipe hose clamp 2
Disconnect the connector arrow.?Remove the noise insulation. Refer to see Noise Insulation; Overview - Noise Insulation.
?Remove the bolts 1 and 4 and remove the air guide hose downward from the Throttle Valve Control Module J338.
?Remove the air guide hose 1 from the charge air cooler and remove the air guide pipe downward.
Disconnect the connector 1 from the Engine Speed Sensor G28.?Remove the Engine Speed Sensor G28 bolt.

G28 IS SUPER SECRET CODE FOR CKP. (USA NAMES)

Sorry , no reset for the fuel pump . Reduced engine power message is for the TAC - throttle actuator control system . Electronic throttle control . Reduced Engine Power: Throttle Actuator Control (TAC) System Description for the 3.6L engine or Throttle Actuator Control (TAC) System Description.TAC System Default Actions/Reduce Power Modes
There are 2 reduce power modes that the engine control module (ECM) can default to if an error is detected in the throttle actuator control (TAC) system. If an accelerator pedal position (APP) sensor 1 or APP sensor 2 circuit fault, throttle position (TP) sensor 2 circuit fault, or if a TP sensor 1 circuit fault is detected with some APP angle, the ECM goes into one of the 2 reduce power modes. In this mode, the engine torque is limited so that the vehicle cannot reach speeds of more than 100 km/h (60 mph). The ECM remains in this reduce power mode during the entire ignition cycle even if the fault is corrected.
If there is a condition with the throttle actuator control circuits, throttle actuator command vs actual position fault, return spring check fault, or a TP sensor 1 circuit fault, the ECM goes into the other reduce engine power mode. In this mode, the engine speed is limited to 2,500 RPM and the 3-6 fuel injectors are randomly turned OFF. At this time the Reduced Power indicator is commanded ON. The ECM remains in the reduce power mode during the entire ignition cycle even if the fault is corrected. Observe, if a TP sensor 1 or throttle actuator control circuit fault is present at the time the vehicle is at idle, with no accelerator pedal angle, the engine may stall.

I have 2013 Chrysler 200. if you go from your air filter to fuel injection on mine it is to the air intake the throttle body and sending unit should be in the line from air filter. The throttle body will be attached to air intake and position sensor attached to throttle body. Not sure about yours mine is one piece.

3.3L for petrol and 5.2L for Diesel.

Probably replaced a good sensor. This codes could be from a bad sensor, a vacuum leak, or an exhaust leak before the sensor.

The MAP sensor on a 2000 Hyundai Elantra will be located directly on top of the intake manifold, 3-4 inches to the left of the throttle body (facing the engine), and attached by two 10mm bolts. However, some 2000 models may not have a MAP sensor, since it was added midway through the production year to prep for the updated 2001 elantra.

It is in the air intake pipe by the throttle body

Hi and welcome to FixYa!

This can be caused by a faulty MAF (mass air flow) sensor or TPS (throttle position sensor). If one of this sensor is faulty the engine tends to speed up, slow down or have an erratic idle. Have it checked and replace if necessary.

Hope this helps and thank you for using FixYa! Have a good one!

Find the Air Intake tube and follow it to the engine. Once at the engine you are at the throttle body, the throttle sensor is mounted to the side of the throttle body on it.