2003 mazda tribute has a red house that intermittently appears, what does this mean?

I need help replacing my thermostat on my 2004 Mazda

JustAnswer https://www.justanswer.com > Mazda Repair
Dec 2, 2015 - The thermostat housing is bolted with 3 bolts to the end of the head closest to the drivers side fender. Thanks for letting me assist you. I ...

1 answer · Top answer: Welcome, I'm Chris and independent contractor that helps customers here. The best way to flush ...

Thermostat replacement Mazda Tribute 2001 - 2011

Haynes Manuals https://haynes.com > en-au > tips-tutorials > mazda-tri...
Free advice from Haynes' master mechanics. Full repair guide available for this vehicle. Save time and money with the experts at Haynes.

Need to replace thermostat in my 2005 mazda tribute 2.3.

JustAnswer https://www.justanswer.com > Mazda Repair
Oct 20, 2022 - 1. Drain the engine coolant. 2. Remove the accessory drive belt tensioner. 3. Remove the thermostat and thermostat housing assembly. ^ Loosen ...

1 answer · Top answer: Good Afternoon, my name is ***** ***** ill be helping you, so sorry to hear about the issues ...

How to change MAZDA TRIBUTE Thermostat

AUTODOC UK https://club.autodoc.co.uk > ... > Thermostat > MAZDA
Illustrated step-by-step manuals and video tutorials on replacing MAZDA TRIBUTE Thermostat will tell you how to carry out DIY replacement of parts and ...

Mazda Tribute Thermostat Housing Pipe Water Outlet V6 ...

Parts Factory https://partsfactoryaus.com.au > product > mazda-tribute-...
Nov 22, 2023 - Mazda Tribute Thermostat Housing with a Replacement Warranty of 3 Years. Our Video Tutorials allow people to save Thermostat replacement cost.
Review by Jay · ‎ A$95.00 · ‎ In stock ..

Yes you need to remove the roof motor module and then move the sun roof to closed and then reinstall the module.

Search Results

Failure of EGR Differential Pressure Sensor : Mazda Tribute ...

repairpal.com > Problems > Mazda > Tribute
Check Engine Light and Hesitation or Stumbling While Driving on Mazda Tribute ...this is my second egr valve and car is not picking up the right sped and when ... Mazda Tribute 2003, replacing burnt DPFE, connector bunrt, Need color pinout. ... Drivetrain · Electrical & Lights · Engine · Exhaust & Emissions · Heating & AC ...

Check Engine Light Diagnosis Cost for Mazda Tribute ...

repairpal.com > Estimator > Mazda > Tribute
A Check Engine Light is turned on when the Mazda Tribute engine control module detects a fault in the emissions system. One or more diagnostic codes will be

No it's extremely simple to change the 2 oxygen sensors get down under the tribute take of plastic shield first one is right their in front of you second one is up and off the the left I did it in 20 mins with very little tools the plastic cover under is 10 mm bolts like 3 of them no problem their is a 3rd one on top on the left under the radiator house you can do thie yourself very easy

On this website you find fuse box diagram and description for Mazda Tribute

Mazda Tribute 2003 2004 fuse box diagram Auto Genius

On this website you find fuse box diagram and description for Mazda Tribute (2003)

Mazda Tribute 2003 2004 fuse box diagram Auto Genius

It's easy, but may need some patience. No need to take off rear door inside panel! Press firmly on the left side of the light housing. It should move towards the right..then pull up slightly and it should pop out from the door panel. Twist the center bulb housing counterclockwise just slightly and the bulb should disconnect from the lense. Pull the bulb out...and replace with new bulb. Replace both sides if you like.

I think the warning light is meant to be in the shape of a radiator - check your coolant level - it generally means your coolant is low. The coolant level sensor often fails on Mazda's however, so your 'problem' might actually be a dodgy sensor not a lack of coolant at all.
Hope this helps, Sherwin

IT SOUNDS LIKE THE IAC VALE OR IDLE AIR CONTROL VALVE IS BAD, WHAT YOU CAN DO IS TAP ON THE VALVE. IT IS LOCATED ON THE INTAKE RIGHT BEHIND THE THROTTLE BODY, JUST TAP ON THE SILVER PART WITH THE BACK OF A SCREW DRIVER A COUPLE OF TIMES. THIS SHOULD UNSTICK THE VALVE AND YOUR TRIBUTE SHOULD RUN. THEN IT IS JUST A MATTER OF REPLACING THE VALVE. YOU CAN GET THEM FROM ANY AUTO PARTS HOUSE.