Hi guys, how can I solve this in a mazda demio, the code is p0894 saying transmission component sliping

Question edited for clarity.

Be careful with terminology, ATF Fluid is a sort of an oil, but it is light in viscosity. Gearbox oil is for vehicles with manual transmission and is considerably thicker and would cause issues in an automatic.

https://www.google.com/search?q=2009+Mazda+Demio+recommended+ATF+fluid

..

Clutches burnt needs rebuilt if clutches fry there's no grabbing it

Fix Your Mazda 3 Stalling Running Rough

transmission component slipping

DTC P0894 Transmission Component Slipping
DTC P0894Circuit Description with 4L80-E / 4L85-E Automatic Transmission The powertrain control module monitors the engine speed and the transmission output shaft speed. The PCM calculates turbine shaft speed and torque converter clutch (TCC) slip speed by using inputs from the automatic transmission input shaft speed sensor, automatic transmission output shaft speed sensor, and other transmission components. The forward clutch housing is used as the AT ISS rotor. Whenever the TCC is engaged, engine speed and turbine speed will closely match, indicating low TCC slip speed. In D3, with the TCC engaged, calculated transmission component slip can only occur in the torque converter. In D4 OVERDRIVE, with the TCC engaged, transmission component slip can occur in the TCC or the fourth clutch assembly. If the PCM detects an excessive TCC slip speed in D4 OVERDRIVE, when the TCC should be engaged, then DTC P0894 sets. DTC P0894 is a type C DTC. For California emissions vehicles, DTC P0894 is a type B DTC.DTC Descriptor This diagnostic procedure supports the following DTC: DTC No MAF sensor DTC P0101, P0102 or P0103. No MAP sensor DTC P0106, P0107 or P0108. No TP sensor DTC P0120 or P0220. No VSS DTC P0502 or P0503. No ISS DTC P0716 or P0717. No TCC Stuck Off DTC P0741. No TCC Stuck On DTC P0742. No 1-2 SS valve DTC P0751, P0752 or P0753. No 2-3 SS valve DTC P0756, P0757 or P0758. No TFP manual valve position switch DTC P1810. No TCC PWM solenoid valve DTC P2761. The throttle angle is 10-100 percent. Engine speed is 1,250-5,000 RPM. The TFT is Vehicle speed is TFP manual valve position switch indicates D4. The TCC is commanded ON for 0.04 second or greater. TCC is locked ON for greater than 0.1 second. Commanded The PCM detects slip in the torque converter clutch and/or the fourth gear clutch pack with the TCC in an apply or locked mode. DTC P0894 sets during the second consecutive trip when one of the following conditions occur: The TCC slip speed is 100-550 for 10 seconds for three occurrences.The TCC slip speed is 100-550 for 10 seconds, the PCM commands maximum line pressure. The TCC slip speed is 100-550 for 12.5 seconds, the PCM commands the TCC Off for 2 seconds. The TCC slip speed is 100-550 for 15 sec For California emission equipped vehicles, the PCM illuminates the malfunction indicator lamp during the second consecutive trip in which the Conditions for Setting the DTC are met. For Federal emission equipped vehicles, the MIL is not illuminated. The PCM commands maximum line pressure. The PCM inhibits the TCC engagement. The PCM freezes transmission adaptive functions. The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame, California only, and Failure Records, California and Federal. The PCM stores the DTC P0894 in PCM history during the second consecutive trip, California, or the first trip, Federal, in which the Conditions for Setting the DTC are met. For California emissions, the PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. A scan tool can clear the MIL/DTC. For California emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring. For Federal emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without a non-emission related diagnostic fault occurring. The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. A TFP manual valve position switch malfunction can set DTC P0894. A mechanical failure of the shift solenoids or TCC PWM solenoid valve can set DTC P0894. Internal transmission failures can result in a DTC P0894. Sticking or contaminated shift valves may cause intermittent slipping in D4. DTC P0894 defaults to an elevated line pressure condition which may result in partial TCC apply. This may produce an idle surge that could stall the engine. The numbers below refer to the step numbers on the diagnostic table. 3. This step tests the indicated range signal to the actual selected range. A faulty TFP manual valve position switch can set a DTC P0894. 4. This step tests for excessive TCC slip speed while in a commanded TCC lock-up state and in fourth gear; and confirms that the fault is present. 5. This step tests for excessive TCC slip speed while in a commanded TCC lock-up state and in third gear. 6. This step tests for a sticking TCC shift valve. 7. This step tests for proper transmission line pressure.

code P0894 is .... transmission component slipping
pcm look for engine rpm when transmission shift and time
if time is too long to drop it raise oil pressure with the force motor to 1 or 2 psi and retest when force motor is at max, then it code P0894
two things component realy slip or force motor is not able to raise pressure
have oil pressure (transmission) check with scan tool raise pressure of force motor to see if able to

Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

P0894 is a Transmission code. It can mean your transmission is slipping. Check the fluid in your transmission.

hi.
the demio has a timing belt.

on a 2005 car, unless you know it has been changed, it is probably due for changing just because it is 6 years old.

Fixed error code P0894 - They replaced torque
convertor, solenoid, filter and did a flush.