Transmission codes what would cause these codes 740, 753, 758, 785, 2761

Here are some possible causes and steps to consider:

Check the transmission fluid level and condition. Shifting issues might be caused by low or filthy transmission fluid. Check that the transmission fluid is at the proper level and seems clean and red. If it is low or polluted, a fluid change and filter replacement may be required.

Transmission Solenoids: Modern automatic transmissions employ solenoids to manage gear shifting. A faulty solenoid might cause the transmission to stay in one gear. If needed, a professional can diagnose and replace malfunctioning solenoids.

Transmission Control Module (TCM): The TCM is in charge of controlling the operation of the transmission. It can cause shifting problems if it malfunctions or receives inaccurate sensor data. Check the TCM for fault codes and functionality.

Wiring and Electrical Issues: Examine the transmission's wiring and electrical connections, especially those to the TCM and sensors. Damaged wires, faulty couplings, or electrical issues can all disrupt transmission operation.
Shifting problems can also be caused by internal mechanical faults within the transmission, such as worn clutches, damaged gears, or a malfunctioning valve body. These problems can be diagnosed and repaired by a competent transmission mechanic.

Transmission Fluid Pressure: Proper gear engagement is dependent on transmission fluid pressure. Shifting might be affected by a malfunction with the transmission pump or pressure regulator. A pressure test can aid in the diagnosis of these problems.

Examine your vehicle for Diagnostic Trouble Codes (DTCs): Even if the knock sensor problem has been rectified, there may be more DTCs associated with the transmission problem. Check for any stored trouble codes with a diagnostic scanner to gain more insight into the problem.

I hope this might be helpful.

Codes P0733 and P0736 on a 2002 Jeep Liberty refer to transmission-related issues. Here's what each code indicates: P0733 - Gear 3 Incorrect Ratio: This code indicates that the transmission is not shifting into the third gear correctly. It suggests a problem with the gear ratio between the input and output shafts of the transmission when the third gear is engaged. This could be caused by issues such as a faulty transmission solenoid, a worn or damaged gear, low transmission fluid level, or internal transmission problems. P0736 - Reverse Incorrect Ratio: This code indicates that the transmission is not shifting into the reverse gear correctly. It suggests a problem with the gear ratio between the input and output shafts of the transmission when the reverse gear is engaged. Possible causes could include a faulty transmission solenoid, a damaged or worn reverse gear, low transmission fluid level, or internal transmission issues.

Possible causes of OBD code P0730
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Shift solenoids harness or connectors - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: The TCM has detected that the transmission is trying to mechanically shift to a lower gear than intended

Possible causes of OBD code P0735
- Low transmission fluid level - Dirty transmission fluid - Shift solenoids - Transmission mechanical problems - Transmission hydraulic control circuit The Error code is generally activated on detection of the following conditions: P0735 is detected when A/T cannot be shifted to the 5th gear position even if electrical circuit is good.

Possible causes of this code are: - Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness is open or shorted
- Torque converter clutch solenoid valve circuit poor electrical connection


Read more: http://engine-codes.com/p0740_chrysler.html#ixzz32x3c6mOw

code p0700 refers to transmission control system/MIL --malfunction===causes --wiring ---TCM (1)
code po740 refers to torque converter clutch (TCC) solenoid--circuit malfunction===causes--wiring--TCC solenoid--ECM/TCM (transmission control module) (again)
code p0871 refers to transmission fluid pressure (TFP) sensor C -range/ performance problem==causes---wiring--poor connection--TFP sensor--ECM /TCM (yet again)
code p0734 refers to gear 3 ratio (po374 is gear ratio 4) incorrect ratio===causes --wiring--TR sensor/switch--shift solenoids--transmission mechanical fault (causes are the same for po733&734)
code po846 refers to transmission fluid pressure (TFP) sensor B-range/ performance problem===causes ---wiring--poor connection--TFP sensor--ECM/TCM (again). Give the clutch a miss as you still have 1st gear and if the clutch is not working you will not be going any where. Have a pressure test done on the transmission to check for internal mechanical failures (pump ). The rest are sensors are wiring connections , sensor and TCM. My bet is the TCM unit. Have it checked out. What ever you do treat any suggestion of a new transmission with a grain of salt until you are shown proof positive that you need one.

p0700 is a transmission overall problem -tcm transmission control module problem u need to have the truck hook up to a diagnostic reader for the transmission -first check the fluid make sure full and not burnt[may need to change fluid and filter other than that their are to many problems that can cause the code

code p0731 p0732 are internal gear ratio trans. codes and p0172 vehicle running rich can also be caused if vehicle trans. is slipping

You must do the diagnostics for each code.
Here are the possibilitesP0740 DODGE - Torque Converter Clutch Circuithttp://engine-codes.com/p0740_dodge.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
P0743 DODGE - Torque Converter Clutch Solenoid Circuithttp://engine-codes.com/p0743_dodge.htmlForum CodePossible causes- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
- Low transmission fluid level
- Dirty transmission fluid

P0753 DODGEP0753 DODGE - 3-4 Shift Solenoid Relayhttp://engine-codes.com/p0753_dodge.htmlForum CodePossible causes- Faulty shift solenoid valve
- Shift solenoid valve harness or connectors
- Shift solenoid valve circuit is open or shorted
- Low transmission fluid level
- Dirty transmission fluid

There is no one fix works for all on these code. Also you have left out the letter and one number of the code I assume these are P0730 and P0733, if so read on.

P0730 CHRYSLER - Incorrect Gear RatioPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Shift solenoids harness or connectors
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0733 CHRYSLER - Gear Ratio Error In Third GearPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

HERE IS THE DIFINTION
Automatic transmission torque converter clutch stuck off.
Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted
- Transmission internal mechanical problem